| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
fbdev: omap2: fix use-after-free in omapfb_mmap
omapfb_mmap() has a race condition with OMAPFB_SETUP_PLANE ioctl that
can lead to use-after-free:
The fb_mmap() entry point holds mm_lock but not lock (fb_info->lock),
while ioctl handlers like OMAPFB_SETUP_PLANE hold lock but not mm_lock.
This allows concurrent execution.
In omapfb_mmap():
1. rg = omapfb_get_mem_region(ofbi->region); // Get old region ref
2. start = omapfb_get_region_paddr(ofbi); // Read from NEW region
3. len = fix->smem_len; // Read from NEW region
4. vm_iomap_memory(vma, start, len); // Map NEW region memory
5. atomic_inc(&rg->map_count); // Increment OLD region!
Concurrently, OMAPFB_SETUP_PLANE can:
- Reassign ofbi->region = new_rg
- Update fix->smem_len
- OMAPFB_SETUP_MEM then checks NEW region's map_count (0!) and frees it
This leaves userspace with a mapping to freed physical memory.
The fix is to read all required values (start, len) from the same
region reference (rg) that will have its map_count incremented,
preventing the region from being freed while still mapped. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm: always recover the gpu
Previously, in case there was no more work to do, recover worker
wouldn't trigger recovery and would instead rely on the gpu going to
sleep and then resuming when more work is submitted.
Recover_worker will first increment the fence of the hung ring so, if
there's only one job submitted to a ring and that causes an hang, it
will early out.
There's no guarantee that the gpu will suspend and resume before more
work is submitted and if the gpu is in a hung state it will stay in that
state and probably trigger a timeout again.
Just stop checking and always recover the gpu.
Patchwork: https://patchwork.freedesktop.org/patch/704066/ |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: Add upper bound check for num_of_nodes
drm/amdkfd: Add upper bound check for num_of_nodes
in kfd_ioctl_get_process_apertures_new.
(cherry picked from commit 98ff46a5ea090c14d2cdb4f5b993b05d74f3949f) |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix fsck inconsistency caused by incorrect nat_entry flag usage
f2fs_need_dentry_mark() reads nat_entry flags without mutual exclusion
with the checkpoint path, which can result in an incorrect inode block
marking state. The scenario is as follows:
create & write & fsync 'file A' write checkpoint
- f2fs_do_sync_file // inline inode
- f2fs_write_inode // inode folio is dirty
- f2fs_write_checkpoint
- f2fs_flush_merged_writes
- f2fs_sync_node_pages
- f2fs_fsync_node_pages // no dirty node
- f2fs_need_inode_block_update // return true
- f2fs_fsync_node_pages // inode dirtied
- f2fs_need_dentry_mark //return true
- f2fs_flush_nat_entries
- f2fs_write_checkpoint end
- __write_node_folio // inode with DENT_BIT_SHIFT set
SPO, "fsck --dry-run" find inode has already checkpointed but still
with DENT_BIT_SHIFT set
The state observed by f2fs_need_dentry_mark() can differ from the state
observed in __write_node_folio() after acquiring sbi->node_write. The
root cause is that the semantics of IS_CHECKPOINTED and
HAS_FSYNCED_INODE are only guaranteed after the checkpoint write has
fully completed.
This patch moves set_dentry_mark() into __write_node_folio() and
protects it with the sbi->node_write lock. |
| In the Linux kernel, the following vulnerability has been resolved:
hsr: Remove WARN_ONCE() in hsr_addr_is_self().
syzbot reported the warning [0] in hsr_addr_is_self(),
whose assumption is simply wrong.
hsr->self_node is cleared in hsr_del_self_node(), which
is called from hsr_dellink().
Since dev->rtnl_link_ops->dellink() is called before
unregister_netdevice_many(), there is a window when
user can find the device but without hsr->self_node.
Let's remove WARN_ONCE() in hsr_addr_is_self().
[0]:
HSR: No self node
WARNING: net/hsr/hsr_framereg.c:39 at hsr_addr_is_self+0x211/0x3f0 net/hsr/hsr_framereg.c:39, CPU#0: syz.4.16848/17220
Modules linked in:
CPU: 0 UID: 0 PID: 17220 Comm: syz.4.16848 Tainted: G L syzkaller #0 PREEMPT_{RT,(full)}
Tainted: [L]=SOFTLOCKUP
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/18/2026
RIP: 0010:hsr_addr_is_self+0x211/0x3f0 net/hsr/hsr_framereg.c:39
Code: 33 2f 41 0f b7 dd 89 ee 09 de 31 ff e8 c8 b4 c6 f6 09 dd 74 54 e8 0f b0 c6 f6 31 ed eb 53 e8 06 b0 c6 f6 48 8d 3d 2f 50 9c 04 <67> 48 0f b9 3a 31 ed eb 42 e8 c1 13 1f 00 89 c5 31 ff 89 c6 e8 96
RSP: 0018:ffffc900041c70e0 EFLAGS: 00010283
RAX: ffffffff8afdc6ca RBX: ffffffff8afdc4e6 RCX: 0000000000080000
RDX: ffffc90010493000 RSI: 0000000000000948 RDI: ffffffff8f9a1700
RBP: 0000000000000001 R08: 0000000000000000 R09: 0000000000000000
R10: ffffc900041c71e8 R11: fffff52000838e3f R12: dffffc0000000000
R13: ffff888041f9e3c0 R14: ffff888086ee3802 R15: 0000000000000000
FS: 00007f6fe985d6c0(0000) GS:ffff888126176000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f80bd437dac CR3: 0000000025096000 CR4: 00000000003526f0
DR0: ffffffffffffffff DR1: 00000000000001f8 DR2: 0000000000000002
DR3: ffffffffefffff15 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
check_local_dest net/hsr/hsr_forward.c:592 [inline]
fill_frame_info net/hsr/hsr_forward.c:728 [inline]
hsr_forward_skb+0xa11/0x2a80 net/hsr/hsr_forward.c:739
hsr_dev_xmit+0x253/0x370 net/hsr/hsr_device.c:236
__netdev_start_xmit include/linux/netdevice.h:5368 [inline]
netdev_start_xmit include/linux/netdevice.h:5377 [inline]
xmit_one net/core/dev.c:3888 [inline]
dev_hard_start_xmit+0x2df/0x860 net/core/dev.c:3904
__dev_queue_xmit+0x1428/0x3900 net/core/dev.c:4870
neigh_output include/net/neighbour.h:556 [inline]
ip_finish_output2+0xcec/0x10b0 net/ipv4/ip_output.c:237
ip_send_skb net/ipv4/ip_output.c:1510 [inline]
ip_push_pending_frames+0x8b/0x110 net/ipv4/ip_output.c:1530
raw_sendmsg+0x1547/0x1a50 net/ipv4/raw.c:659
sock_sendmsg_nosec net/socket.c:787 [inline]
__sock_sendmsg net/socket.c:802 [inline]
____sys_sendmsg+0x7da/0x9c0 net/socket.c:2698
___sys_sendmsg+0x2a5/0x360 net/socket.c:2752
__sys_sendmsg net/socket.c:2784 [inline]
__do_sys_sendmsg net/socket.c:2789 [inline]
__se_sys_sendmsg net/socket.c:2787 [inline]
__x64_sys_sendmsg+0x1c3/0x2a0 net/socket.c:2787
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0x15f/0xf80 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f6feb62ce59
Code: ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 e8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f6fe985d028 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007f6feb8a6090 RCX: 00007f6feb62ce59
RDX: 0000000000000000 RSI: 0000200000000000 RDI: 0000000000000004
RBP: 00007f6feb6c2d6f R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 00007f6feb8a6128 R14: 00007f6feb8a6090 R15: 00007ffcf01cc488
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: Don't WARN if memory is dirtied without a vCPU when the VM is dying
When marking a page dirty, complain about not having a running/loaded vCPU
if and only if the VM is still alive, i.e. its refcount is non-zero. This
will allow fixing a memory leak for x86 SEV-ES guests without hitting what
is effectively a false positive on the WARN.
For some SEV-ES VM-Exits, KVM keeps a writable mapping of a guest page
across an exit to userspace, and typically unmaps the page on the next
KVM_RUN. But if userspace never calls KVM_RUN after such an exit, then KVM
needs to unmap the page when the vCPU is destroyed, which in turn triggers
the WARN about not having a running vCPU.
Alternatively, SEV-ES could temporarily load the vCPU to suppress the WARN,
as is done in nested_vmx_free_vcpu() (but for completely unrelated reasons;
suppressing WARN from nested_put_vmcs12_pages() is pure happenstance). But
loading a vCPU during destruction is gross (ideally nVMX code would be
cleaned up), risks complicating the SEV-ES code (KVM would need to ensure
the temporarily load()+put() only runs when the vCPU isn't already loaded),
and is ultimately pointless.
The motivation for the WARN is to guard against KVM dirtying guest memory
without pushing the corresponding GFN to the active vCPU's dirty ring, e.g.
to ensure userspace doesn't miss a dirty page. But for the VM's refcount
to reach zero, there can't be _any_ userspace mappings to the dirty ring,
as mapping the dirty ring requires doing mmap() on the vCPU FD. I.e. if
userspace had a valid mapping for the dirty ring, then the vCPU file and
thus the owning VM would still be alive. And so since userspace can't
possibly reach the dirty ring, whether or not KVM technically "misses" a
push to the dirty ring is irrelevant. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Fix out-of-bounds read in dp_get_eq_aux_rd_interval()
[Why & How]
The aux_rd_interval array in struct dc_lttpr_caps is declared with
MAX_REPEATER_CNT - 1 (7) elements, indexed 0..6. However, the offset
parameter passed to dp_get_eq_aux_rd_interval() can be as large as
MAX_REPEATER_CNT (8) when a sink reports 8 LTTPR repeaters via DPCD.
This leads to an out-of-bounds read of aux_rd_interval[7] when offset
is 8.
Fix this by growing aux_rd_interval to MAX_REPEATER_CNT elements to
accommodate the full range of valid repeater counts defined by the DP
spec.
(cherry picked from commit a55a458a8df37a65ffda5cf721d554a8f74f6b04) |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7921: Place upper limit on station AID
Any station configured with an AID over 20 causes a firmware crash.
This situation occurred in our testing using an AP interface on 7922
hardware, with a modified hostapd, sourced from Mediatek's OpenWRT
feeds.
In stock hostapd, station AIDs begin counting at 1, and this
configuration is prevented with an upper limit on associated stations.
However, the modified hostapd began allocation at 65, which caused the
firmware to crash. This fix does not allow these AIDs to work, but will
prevent the firmware crash.
This crash was only seen on IFTYPE_AP interfaces, and the fix does not
appear to have an effect on IFTYPE_STATION behavior. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Avoid NULL dereference in dc_dmub_srv error paths
In dc_dmub_srv_log_diagnostic_data() and
dc_dmub_srv_enable_dpia_trace().
Both functions check:
if (!dc_dmub_srv || !dc_dmub_srv->dmub)
and then call DC_LOG_ERROR() inside that block.
DC_LOG_ERROR() uses dc_dmub_srv->ctx internally. So if
dc_dmub_srv is NULL, the logging itself can dereference a
NULL pointer and cause a crash.
Fix this by splitting the checks.
First check if dc_dmub_srv is NULL and return immediately.
Then check dc_dmub_srv->dmub and log the error only when
dc_dmub_srv is valid.
Fixes the below:
../display/dc/dc_dmub_srv.c:962 dc_dmub_srv_log_diagnostic_data() error: we previously assumed 'dc_dmub_srv' could be null (see line 961)
../display/dc/dc_dmub_srv.c:1167 dc_dmub_srv_enable_dpia_trace() error: we previously assumed 'dc_dmub_srv' could be null (see line 1166) |
| In the Linux kernel, the following vulnerability has been resolved:
net: mana: Guard mana_remove against double invocation
If PM resume fails (e.g., mana_attach() returns an error), mana_probe()
calls mana_remove(), which tears down the device and sets
gd->gdma_context = NULL and gd->driver_data = NULL.
However, a failed resume callback does not automatically unbind the
driver. When the device is eventually unbound, mana_remove() is invoked
a second time. Without a NULL check, it dereferences gc->dev with
gc == NULL, causing a kernel panic.
Add an early return if gdma_context or driver_data is NULL so the second
invocation is harmless. Move the dev = gc->dev assignment after the
guard so it cannot dereference NULL. |
| In the Linux kernel, the following vulnerability has been resolved:
net: phonet: do not BUG_ON() in pn_socket_autobind() on failed bind
syzbot reported a kernel BUG triggered from pn_socket_sendmsg() via
pn_socket_autobind():
kernel BUG at net/phonet/socket.c:213!
RIP: 0010:pn_socket_autobind net/phonet/socket.c:213 [inline]
RIP: 0010:pn_socket_sendmsg+0x240/0x250 net/phonet/socket.c:421
Call Trace:
sock_sendmsg_nosec+0x112/0x150 net/socket.c:797
__sock_sendmsg net/socket.c:812 [inline]
__sys_sendto+0x402/0x590 net/socket.c:2280
...
pn_socket_autobind() calls pn_socket_bind() with port 0 and, on
-EINVAL, assumes the socket was already bound and asserts that the
port is non-zero:
err = pn_socket_bind(sock, ..., sizeof(struct sockaddr_pn));
if (err != -EINVAL)
return err;
BUG_ON(!pn_port(pn_sk(sock->sk)->sobject));
return 0; /* socket was already bound */
However pn_socket_bind() also returns -EINVAL when sk->sk_state is not
TCP_CLOSE, even when the socket has never been bound and pn_port() is
still 0. In that case the BUG_ON() fires and panics the kernel from a
user-triggerable path.
Treat the "bind returned -EINVAL but pn_port() is still 0" case as a
regular error and propagate -EINVAL to the caller instead of crashing.
Existing callers already translate a non-zero return from
pn_socket_autobind() into -ENOBUFS/-EAGAIN, so returning -EINVAL here
only changes behaviour from panic to a normal errno. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: only release the dirty pages io tree after successful writes
[WARNING]
With extra warning on dirty extent buffers at umount (aka, the next
patch in the series), test case generic/388 can trigger the following
warning about dirty extent buffers at unmount time:
BTRFS critical (device dm-2 state E): emergency shutdown
BTRFS error (device dm-2 state E): error while writing out transaction: -30
BTRFS warning (device dm-2 state E): Skipping commit of aborted transaction.
BTRFS error (device dm-2 state EA): Transaction 9 aborted (error -30)
BTRFS: error (device dm-2 state EA) in cleanup_transaction:2068: errno=-30 Readonly filesystem
BTRFS info (device dm-2 state EA): forced readonly
BTRFS info (device dm-2 state EA): last unmount of filesystem 4fbf2e15-f941-49a0-bc7c-716315d2777c
------------[ cut here ]------------
WARNING: disk-io.c:3311 at invalidate_and_check_btree_folios+0xfd/0x1ca [btrfs], CPU#8: umount/914368
CPU: 8 UID: 0 PID: 914368 Comm: umount Tainted: G OE 7.1.0-rc1-custom+ #372 PREEMPT(full) 2de38db8d1deae71fde295430a0ff3ab98ccf596
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS unknown 02/02/2022
RIP: 0010:invalidate_and_check_btree_folios+0xfd/0x1ca [btrfs]
Call Trace:
<TASK>
close_ctree+0x52e/0x574 [btrfs d2f0b1cd330d1287e7a9919d112eadfc0e914efd]
generic_shutdown_super+0x89/0x1a0
kill_anon_super+0x16/0x40
btrfs_kill_super+0x16/0x20 [btrfs d2f0b1cd330d1287e7a9919d112eadfc0e914efd]
deactivate_locked_super+0x2d/0xb0
cleanup_mnt+0xdc/0x140
task_work_run+0x5a/0xa0
exit_to_user_mode_loop+0x123/0x4b0
do_syscall_64+0x243/0x7c0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
</TASK>
---[ end trace 0000000000000000 ]---
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30539776 owner 9 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30621696 owner 257 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30638080 owner 258 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30654464 owner 7 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30703616 owner 2 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30720000 owner 10 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30736384 owner 4 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30752768 owner 11 gen 9 refs 2 flags 0x7
I'm using a stripped down version, which seems to trigger the warning
more reliably:
_fsstress_pid=""
workload()
{
dmesg -C
mkfs.btrfs -f -K $dev > /dev/null
echo 1 > /sys/kernel/debug/clear_warn_once
mount $dev $mnt
$fsstress -w -n 1024 -p 4 -d $mnt &
_fsstress_pid=$!
sleep 0
$godown $mnt
pkill --echo -PIPE fsstress > /dev/null
wait $_fsstress_pid
unset _fsstress_pid
umount $mnt
if dmesg | grep -q "WARNING"; then
fail
fi
}
for (( i = 0; i < $runtime; i++ )); do
echo "=== $i/$runtime ==="
workload
done
[CAUSE]
Inside btrfs_write_and_wait_transaction(), we first try to write all
dirty ebs, then wait for them to finish.
After that we call btrfs_extent_io_tree_release() to free all
extent states from dirty_pages io tree.
However if we hit an error from btrfs_write_marked_extent(), then we
still call btrfs_extent_io_tree_release() to clear that dirty_pages io
tree, which may contain dirty records that we haven't yet submitted.
Furthermore, the later transaction cleanup path will utilize that
dirty_pages io tree to properly cleanup those dirty ebs, but since it's
already empty, no dirty ebs are properly cleaned up, thus will later
trigger the warnings inside invalidate_btree_folios().
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
erofs: fix use-after-free on sbi->sync_decompress
z_erofs_decompress_kickoff() can race with filesystem unmount, causing
a use-after-free on sbi->sync_decompress.
When I/O completes, z_erofs_endio() calls z_erofs_decompress_kickoff()
to queue z_erofs_decompressqueue_work() asynchronously. Then, after all
folios are unlocked, unmount workflow can proceed and sbi will be freed
before accessing to sbi->sync_decompress.
Thread (unmount) I/O completion kworker
queue_work
z_erofs_decompressqueue_work
(all folios are unlocked)
cleanup_mnt
..
erofs_kill_sb
erofs_sb_free
kfree(sbi)
access sbi->sync_decompress // UAF!! |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nft_ct: bail out on template ct in get eval
I noticed this issue while looking at a historic syzbot report [1].
A rule like the one below is enough to trigger the bug:
table ip t {
chain pre {
type filter hook prerouting priority raw;
ct zone set 1
ct original saddr 1.2.3.4 accept
}
}
The first expression attaches a per-cpu template ct via
nft_ct_set_zone_eval() (nf_ct_tmpl_alloc -> kzalloc, tuple is all
zero, nf_ct_l3num(ct) == 0). The next expression then calls
nft_ct_get_eval() on the same skb, treats the template as a real ct
and hits the 16-byte memcpy path. With dreg at NFT_REG32_15 this
overflows past struct nft_regs on the kernel stack; with smaller
dreg values it silently clobbers adjacent registers.
Reject template ct at the eval entry and in nft_ct_get_fast_eval(),
mirroring the check nft_ct_set_eval() already has. Additionally,
bound the address copy in NFT_CT_SRC / NFT_CT_DST by priv->len
instead of by nf_ct_l3num(ct): nf_ct_get_tuple() zeroes the tuple
before pkt_to_tuple() fills in only the protocol-relevant leading
bytes, so the trailing bytes of tuple->{src,dst}.u3.all are
well-defined zero. priv->len is validated at rule load, so the
copy size is now bounded by the destination register rather than
by an untrusted field on the conntrack.
[1]: https://syzkaller.appspot.com/bug?id=389cf09cb72926114fce90dc85a2c3231dcb647c |
| In the Linux kernel, the following vulnerability has been resolved:
l2tp: pppol2tp: hold reference to session in pppol2tp_ioctl()
pppol2tp_ioctl() read sock->sk->sk_user_data directly without any
locks or reference counting. If a controllable sleep was induced during
copy_from_user() (e.g. via a userfaultfd page fault sleep), a concurrent
socket close could trigger pppol2tp_session_close() asynchronously. This
frees the l2tp_session structure via the l2tp_session_del_work workqueue.
Upon resuming, the ioctl thread dereferences the stale session pointer,
resulting in a Use-After-Free (UAF).
Fix this by securely fetching the session reference using the RCU-safe,
refcounted helper pppol2tp_sock_to_session(sk) on entry. This locks the
session's refcount across the sleep. We structured the function to exit
via standard err breaks, guaranteeing that l2tp_session_put() is cleanly
called on all return paths to drop the reference.
To preserve existing behavior we validate the session and its magic
signature only for the specific L2TP commands that require it. This
ensures that generic/unknown ioctls called on an unconnected socket
still return -ENOIOCTLCMD and correctly fall back to generic handlers
(e.g. in sock_do_ioctl()). |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: fix leak if split 6 GHz scanning fails
rdev->int_scan_req is leaked if cfg80211_scan() fails. Note that it's
supposed to be released at ___cfg80211_scan_done() but this doesn't happen
as rdev->scan_req is NULL at that point, too, leading to the early return
from the freeing function.
unreferenced object 0xffff8881161d0800 (size 512):
comm "wpa_supplicant", pid 379, jiffies 4294749765
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 f0 81 13 16 81 88 ff ff ................
backtrace (crc c867fdb6):
kmemleak_alloc+0x89/0x90
__kmalloc_noprof+0x2fd/0x410
cfg80211_scan+0x133/0x730
nl80211_trigger_scan+0xc69/0x1cc0
genl_family_rcv_msg_doit+0x204/0x2f0
genl_rcv_msg+0x431/0x6b0
netlink_rcv_skb+0x143/0x3f0
genl_rcv+0x27/0x40
netlink_unicast+0x4f6/0x820
netlink_sendmsg+0x797/0xce0
__sock_sendmsg+0xc4/0x160
____sys_sendmsg+0x5e4/0x890
___sys_sendmsg+0xf8/0x180
__sys_sendmsg+0x136/0x1e0
__x64_sys_sendmsg+0x76/0xc0
x64_sys_call+0x13f0/0x17d0
Found by Linux Verification Center (linuxtesting.org). |
| In the Linux kernel, the following vulnerability has been resolved:
gpio: mvebu: fix NULL pointer dereference in suspend/resume
mvebu_pwm_suspend() and mvebu_pwm_resume() are called for all GPIO
banks during suspend/resume, but not all banks have PWM functionality.
GPIO banks without PWM have mvchip->mvpwm set to NULL.
Calling mvebu_pwm_suspend() with mvpwm == NULL causes a NULL pointer
dereference when it tries to access mvpwm->blink_select.
Unable to handle kernel NULL pointer dereference at virtual address 00000020 when write
[00000020] *pgd=00000000
Internal error: Oops: 815 [#1] PREEMPT ARM
Modules linked in:
CPU: 0 UID: 0 PID: 406 Comm: sh Not tainted 6.12.74-rt12-yocto-standard-g4e96f98fb7db-dirty #353
Hardware name: Marvell Armada 370/XP (Device Tree)
PC is at regmap_mmio_read+0x38/0x54
LR is at regmap_mmio_read+0x38/0x54
pc : [<c05fd2ac>] lr : [<c05fd2ac>] psr: 200f0013
sp : f0c11d10 ip : 00000000 fp : c100d2f0
r10: c14fb854 r9 : 00000000 r8 : 00000000
r7 : c1799c00 r6 : 00000020 r5 : 00000020 r4 : c179c7c0
r3 : f0a231a0 r2 : 00000020 r1 : 00000020 r0 : 00000000
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c5387d Table: 135ec059 DAC: 00000051
Call trace:
regmap_mmio_read from _regmap_bus_reg_read+0x78/0xac
_regmap_bus_reg_read from _regmap_read+0x60/0x154
_regmap_read from regmap_read+0x3c/0x60
regmap_read from mvebu_gpio_suspend+0xa4/0x14c
mvebu_gpio_suspend from dpm_run_callback+0x54/0x180
dpm_run_callback from device_suspend+0x124/0x630
device_suspend from dpm_suspend+0x124/0x270
dpm_suspend from dpm_suspend_start+0x64/0x6c
dpm_suspend_start from suspend_devices_and_enter+0x140/0x8e8
suspend_devices_and_enter from pm_suspend+0x2fc/0x308
pm_suspend from state_store+0x6c/0xc8
state_store from kernfs_fop_write_iter+0x10c/0x1f8
kernfs_fop_write_iter from vfs_write+0x270/0x468
vfs_write from ksys_write+0x70/0xf0
ksys_write from ret_fast_syscall+0x0/0x54
Add a NULL check for mvchip->mvpwm before calling the PWM
suspend/resume functions. |
| In the Linux kernel, the following vulnerability has been resolved:
net: phy: clean the sfp upstream if phy probing fails
Sashiko reported that we don't call sfp_bus_del_upstream() in the probe
failure path, so let's add it, otherwise the sfp-bus is left with a
dangling 'upstream' field, that may be used later on during SFP events.
This issue existed before the generic phylib sfp support, back when
drivers were calling phy_sfp_probe themselves. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5: Fix slab-out-of-bounds in mlx5_query_nic_vport_mac_list
mlx5_query_nic_vport_mac_list() sizes its firmware command buffer using
the PF's log_max_current_uc/mc_list capabilities. When querying a VF
vport with a larger configured max (via devlink), the firmware response
can overflow this buffer:
BUG: KASAN: slab-out-of-bounds in mlx5_query_nic_vport_mac_list+0x453/0x4c0 [mlx5_core]
Read of size 4 at addr ff1100013ffc8a12 by task kworker/u96:2/385
CPU: 12 UID: 0 PID: 385 Comm: kworker/u96:2 Not tainted 7.0.0-rc6+ #1 PREEMPT
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009)
Workqueue: mlx5_esw_wq esw_vport_change_handler [mlx5_core]
Call Trace:
<TASK>
dump_stack_lvl+0x69/0xa0
print_report+0x176/0x4e4
kasan_report+0xc8/0x100
mlx5_query_nic_vport_mac_list+0x453/0x4c0 [mlx5_core]
esw_update_vport_addr_list+0x2e3/0xda0 [mlx5_core]
esw_vport_change_handle_locked+0xa1f/0x1060 [mlx5_core]
esw_vport_change_handler+0x6a/0x90 [mlx5_core]
process_one_work+0x87f/0x15e0
worker_thread+0x62b/0x1020
kthread+0x375/0x490
ret_from_fork+0x4dc/0x810
ret_from_fork_asm+0x11/0x20
</TASK>
Fix by querying the vport's own HCA caps to size the buffer correctly.
Refactor the function to allocate and return the MAC list internally,
removing the caller's dependency on knowing the correct max. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: xsk: Fix DMA and xdp_frame leak on XDP_TX xmit failure
In the XSK branch of mlx5e_xmit_xdp_buff(), when sq->xmit_xdp_frame()
returns false (e.g. XDPSQ is full), the function returns without
unmapping the DMA address or freeing the xdp_frame allocated by
xdp_convert_zc_to_xdp_frame(). The xdpi_fifo push only happens on
success, so the completion path cannot recover these entries.
With CONFIG_DMA_API_DEBUG=y, the leak surfaces on driver unbind:
DMA-API: pci 0000:08:00.0: device driver has pending DMA
allocations while released from device [count=1116]
One of leaked entries details: [device address=0x000000010ffd7028]
[size=1534 bytes] [mapped with DMA_TO_DEVICE] [mapped as phy]
WARNING: kernel/dma/debug.c:881 at dma_debug_device_change+0x127/0x180
...
DMA-API: Mapped at:
debug_dma_map_phys+0x4b/0xd0
dma_map_phys+0xfd/0x2d0
mlx5e_xdp_handle+0x5ae/0xac0 [mlx5_core]
mlx5e_xsk_skb_from_cqe_mpwrq_linear+0xc4/0x170 [mlx5_core]
mlx5e_handle_rx_cqe_mpwrq+0xc1/0x290 [mlx5_core]
Add the missing unmap + xdp_return_frame, matching the cleanup already
done in mlx5e_xdp_xmit(). has_frags is rejected earlier in this branch,
so no per-frag unmap is needed. |
