| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
bnxt_en: Shutdown FW DMA in bnxt_shutdown()
The netif_close() call in bnxt_shutdown() only stops packet DMA. There
may be FW DMA for trace logging (recently added) that will continue. If
we kexec to a new kernel, the DMA will corrupt memory in the new kernel.
Add bnxt_hwrm_func_drv_unrgtr() to unregister the driver from the FW.
This will stop the FW DMA. In case the call fails, call pcie_flr() to
reset the function and stop the DMA. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: Fix mmap write lock not release
If mmap write lock is taken while draining retry fault, mmap write lock
is not released because svm_range_restore_pages calls mmap_read_unlock
then returns. This causes deadlock and system hangs later because mmap
read or write lock cannot be taken.
Downgrade mmap write lock to read lock if draining retry fault fix this
bug. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix infinite loop in __insert_extent_tree()
When we get wrong extent info data, and look up extent_node in rb tree,
it will cause infinite loop (CONFIG_F2FS_CHECK_FS=n). Avoiding this by
return NULL and print some kernel messages in that case. |
| NVIDIA NVTabular for Linux contains a vulnerability in the Workflow component, where a user could cause a deserialization issue. A successful exploit of this vulnerability might lead to code execution, denial of service, information disclosure, and data tampering. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe: Fix oops in xe_gem_fault when running core_hotunplug test.
I saw an oops in xe_gem_fault when running the xe-fast-feedback
testlist against the realtime kernel without debug options enabled.
The panic happens after core_hotunplug unbind-rebind finishes.
Presumably what happens is that a process mmaps, unlocks because
of the FAULT_FLAG_RETRY_NOWAIT logic, has no process memory left,
causing ttm_bo_vm_dummy_page() to return VM_FAULT_NOPAGE, since
there was nothing left to populate, and then oopses in
"mem_type_is_vram(tbo->resource->mem_type)" because tbo->resource
is NULL.
It's convoluted, but fits the data and explains the oops after
the test exits. |
| In the Linux kernel, the following vulnerability has been resolved:
futex: Don't leak robust_list pointer on exec race
sys_get_robust_list() and compat_get_robust_list() use ptrace_may_access()
to check if the calling task is allowed to access another task's
robust_list pointer. This check is racy against a concurrent exec() in the
target process.
During exec(), a task may transition from a non-privileged binary to a
privileged one (e.g., setuid binary) and its credentials/memory mappings
may change. If get_robust_list() performs ptrace_may_access() before
this transition, it may erroneously allow access to sensitive information
after the target becomes privileged.
A racy access allows an attacker to exploit a window during which
ptrace_may_access() passes before a target process transitions to a
privileged state via exec().
For example, consider a non-privileged task T that is about to execute a
setuid-root binary. An attacker task A calls get_robust_list(T) while T
is still unprivileged. Since ptrace_may_access() checks permissions
based on current credentials, it succeeds. However, if T begins exec
immediately afterwards, it becomes privileged and may change its memory
mappings. Because get_robust_list() proceeds to access T->robust_list
without synchronizing with exec() it may read user-space pointers from a
now-privileged process.
This violates the intended post-exec access restrictions and could
expose sensitive memory addresses or be used as a primitive in a larger
exploit chain. Consequently, the race can lead to unauthorized
disclosure of information across privilege boundaries and poses a
potential security risk.
Take a read lock on signal->exec_update_lock prior to invoking
ptrace_may_access() and accessing the robust_list/compat_robust_list.
This ensures that the target task's exec state remains stable during the
check, allowing for consistent and synchronized validation of
credentials. |
| In the Linux kernel, the following vulnerability has been resolved:
net/smc: fix general protection fault in __smc_diag_dump
The syzbot report a crash:
Oops: general protection fault, probably for non-canonical address 0xfbd5a5d5a0000003: 0000 [#1] SMP KASAN NOPTI
KASAN: maybe wild-memory-access in range [0xdead4ead00000018-0xdead4ead0000001f]
CPU: 1 UID: 0 PID: 6949 Comm: syz.0.335 Not tainted syzkaller #0 PREEMPT(full)
Hardware name: Google Compute Engine/Google Compute Engine, BIOS Google 08/18/2025
RIP: 0010:smc_diag_msg_common_fill net/smc/smc_diag.c:44 [inline]
RIP: 0010:__smc_diag_dump.constprop.0+0x3ca/0x2550 net/smc/smc_diag.c:89
Call Trace:
<TASK>
smc_diag_dump_proto+0x26d/0x420 net/smc/smc_diag.c:217
smc_diag_dump+0x27/0x90 net/smc/smc_diag.c:234
netlink_dump+0x539/0xd30 net/netlink/af_netlink.c:2327
__netlink_dump_start+0x6d6/0x990 net/netlink/af_netlink.c:2442
netlink_dump_start include/linux/netlink.h:341 [inline]
smc_diag_handler_dump+0x1f9/0x240 net/smc/smc_diag.c:251
__sock_diag_cmd net/core/sock_diag.c:249 [inline]
sock_diag_rcv_msg+0x438/0x790 net/core/sock_diag.c:285
netlink_rcv_skb+0x158/0x420 net/netlink/af_netlink.c:2552
netlink_unicast_kernel net/netlink/af_netlink.c:1320 [inline]
netlink_unicast+0x5a7/0x870 net/netlink/af_netlink.c:1346
netlink_sendmsg+0x8d1/0xdd0 net/netlink/af_netlink.c:1896
sock_sendmsg_nosec net/socket.c:714 [inline]
__sock_sendmsg net/socket.c:729 [inline]
____sys_sendmsg+0xa95/0xc70 net/socket.c:2614
___sys_sendmsg+0x134/0x1d0 net/socket.c:2668
__sys_sendmsg+0x16d/0x220 net/socket.c:2700
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xcd/0x4e0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
</TASK>
The process like this:
(CPU1) | (CPU2)
---------------------------------|-------------------------------
inet_create() |
// init clcsock to NULL |
sk = sk_alloc() |
|
// unexpectedly change clcsock |
inet_init_csk_locks() |
|
// add sk to hash table |
smc_inet_init_sock() |
smc_sk_init() |
smc_hash_sk() |
| // traverse the hash table
| smc_diag_dump_proto
| __smc_diag_dump()
| // visit wrong clcsock
| smc_diag_msg_common_fill()
// alloc clcsock |
smc_create_clcsk |
sock_create_kern |
With CONFIG_DEBUG_LOCK_ALLOC=y, the smc->clcsock is unexpectedly changed
in inet_init_csk_locks(). The INET_PROTOSW_ICSK flag is no need by smc,
just remove it.
After removing the INET_PROTOSW_ICSK flag, this patch alse revert
commit 6fd27ea183c2 ("net/smc: fix lacks of icsk_syn_mss with IPPROTO_SMC")
to avoid casting smc_sock to inet_connection_sock. |
| In the Linux kernel, the following vulnerability has been resolved:
perf/x86/intel: Fix KASAN global-out-of-bounds warning
When running "perf mem record" command on CWF, the below KASAN
global-out-of-bounds warning is seen.
==================================================================
BUG: KASAN: global-out-of-bounds in cmt_latency_data+0x176/0x1b0
Read of size 4 at addr ffffffffb721d000 by task dtlb/9850
Call Trace:
kasan_report+0xb8/0xf0
cmt_latency_data+0x176/0x1b0
setup_arch_pebs_sample_data+0xf49/0x2560
intel_pmu_drain_arch_pebs+0x577/0xb00
handle_pmi_common+0x6c4/0xc80
The issue is caused by below code in __grt_latency_data(). The code
tries to access x86_hybrid_pmu structure which doesn't exist on
non-hybrid platform like CWF.
WARN_ON_ONCE(hybrid_pmu(event->pmu)->pmu_type == hybrid_big)
So add is_hybrid() check before calling this WARN_ON_ONCE to fix the
global-out-of-bounds access issue. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/sysfb: Do not dereference NULL pointer in plane reset
The plane state in __drm_gem_reset_shadow_plane() can be NULL. Do not
deref that pointer, but forward NULL to the other plane-reset helpers.
Clears plane->state to NULL.
v2:
- fix typo in commit description (Javier) |
| In the Linux kernel, the following vulnerability has been resolved:
sched_ext: Fix unsafe locking in the scx_dump_state()
For built with CONFIG_PREEMPT_RT=y kernels, the dump_lock will be converted
sleepable spinlock and not disable-irq, so the following scenarios occur:
inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
irq_work/0/27 [HC0[0]:SC0[0]:HE1:SE1] takes:
(&rq->__lock){?...}-{2:2}, at: raw_spin_rq_lock_nested+0x2b/0x40
{IN-HARDIRQ-W} state was registered at:
lock_acquire+0x1e1/0x510
_raw_spin_lock_nested+0x42/0x80
raw_spin_rq_lock_nested+0x2b/0x40
sched_tick+0xae/0x7b0
update_process_times+0x14c/0x1b0
tick_periodic+0x62/0x1f0
tick_handle_periodic+0x48/0xf0
timer_interrupt+0x55/0x80
__handle_irq_event_percpu+0x20a/0x5c0
handle_irq_event_percpu+0x18/0xc0
handle_irq_event+0xb5/0x150
handle_level_irq+0x220/0x460
__common_interrupt+0xa2/0x1e0
common_interrupt+0xb0/0xd0
asm_common_interrupt+0x2b/0x40
_raw_spin_unlock_irqrestore+0x45/0x80
__setup_irq+0xc34/0x1a30
request_threaded_irq+0x214/0x2f0
hpet_time_init+0x3e/0x60
x86_late_time_init+0x5b/0xb0
start_kernel+0x308/0x410
x86_64_start_reservations+0x1c/0x30
x86_64_start_kernel+0x96/0xa0
common_startup_64+0x13e/0x148
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&rq->__lock);
<Interrupt>
lock(&rq->__lock);
*** DEADLOCK ***
stack backtrace:
CPU: 0 UID: 0 PID: 27 Comm: irq_work/0
Call Trace:
<TASK>
dump_stack_lvl+0x8c/0xd0
dump_stack+0x14/0x20
print_usage_bug+0x42e/0x690
mark_lock.part.44+0x867/0xa70
? __pfx_mark_lock.part.44+0x10/0x10
? string_nocheck+0x19c/0x310
? number+0x739/0x9f0
? __pfx_string_nocheck+0x10/0x10
? __pfx_check_pointer+0x10/0x10
? kvm_sched_clock_read+0x15/0x30
? sched_clock_noinstr+0xd/0x20
? local_clock_noinstr+0x1c/0xe0
__lock_acquire+0xc4b/0x62b0
? __pfx_format_decode+0x10/0x10
? __pfx_string+0x10/0x10
? __pfx___lock_acquire+0x10/0x10
? __pfx_vsnprintf+0x10/0x10
lock_acquire+0x1e1/0x510
? raw_spin_rq_lock_nested+0x2b/0x40
? __pfx_lock_acquire+0x10/0x10
? dump_line+0x12e/0x270
? raw_spin_rq_lock_nested+0x20/0x40
_raw_spin_lock_nested+0x42/0x80
? raw_spin_rq_lock_nested+0x2b/0x40
raw_spin_rq_lock_nested+0x2b/0x40
scx_dump_state+0x3b3/0x1270
? finish_task_switch+0x27e/0x840
scx_ops_error_irq_workfn+0x67/0x80
irq_work_single+0x113/0x260
irq_work_run_list.part.3+0x44/0x70
run_irq_workd+0x6b/0x90
? __pfx_run_irq_workd+0x10/0x10
smpboot_thread_fn+0x529/0x870
? __pfx_smpboot_thread_fn+0x10/0x10
kthread+0x305/0x3f0
? __pfx_kthread+0x10/0x10
ret_from_fork+0x40/0x70
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1a/0x30
</TASK>
This commit therefore use rq_lock_irqsave/irqrestore() to replace
rq_lock/unlock() in the scx_dump_state(). |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: starfive - Correctly handle return of sg_nents_for_len
The return value of sg_nents_for_len was assigned to an unsigned long
in starfive_hash_digest, causing negative error codes to be converted
to large positive integers.
Add error checking for sg_nents_for_len and return immediately on
failure to prevent potential buffer overflows. |
| In the Linux kernel, the following vulnerability has been resolved:
net: netpoll: initialize work queue before error checks
Prevent a kernel warning when netconsole setup fails on devices with
IFF_DISABLE_NETPOLL flag. The warning (at kernel/workqueue.c:4242 in
__flush_work) occurs because the cleanup path tries to cancel an
uninitialized work queue.
When __netpoll_setup() encounters a device with IFF_DISABLE_NETPOLL,
it fails early and calls skb_pool_flush() for cleanup. This function
calls cancel_work_sync(&np->refill_wq), but refill_wq hasn't been
initialized yet, triggering the warning.
Move INIT_WORK() to the beginning of __netpoll_setup(), ensuring the
work queue is properly initialized before any potential failure points.
This allows the cleanup path to safely cancel the work queue regardless
of where the setup fails. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/amd: Fix potential out-of-bounds read in iommu_mmio_show
In iommu_mmio_write(), it validates the user-provided offset with the
check: `iommu->dbg_mmio_offset > iommu->mmio_phys_end - 4`.
This assumes a 4-byte access. However, the corresponding
show handler, iommu_mmio_show(), uses readq() to perform an 8-byte
(64-bit) read.
If a user provides an offset equal to `mmio_phys_end - 4`, the check
passes, and will lead to a 4-byte out-of-bounds read.
Fix this by adjusting the boundary check to use sizeof(u64), which
corresponds to the size of the readq() operation. |
| In the Linux kernel, the following vulnerability has been resolved:
PCI/AER: Avoid NULL pointer dereference in aer_ratelimit()
When platform firmware supplies error information to the OS, e.g., via the
ACPI APEI GHES mechanism, it may identify an error source device that
doesn't advertise an AER Capability and therefore dev->aer_info, which
contains AER stats and ratelimiting data, is NULL.
pci_dev_aer_stats_incr() already checks dev->aer_info for NULL, but
aer_ratelimit() did not, leading to NULL pointer dereferences like this one
from the URL below:
{1}[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 0
{1}[Hardware Error]: event severity: corrected
{1}[Hardware Error]: device_id: 0000:00:00.0
{1}[Hardware Error]: vendor_id: 0x8086, device_id: 0x2020
{1}[Hardware Error]: aer_cor_status: 0x00001000, aer_cor_mask: 0x00002000
BUG: kernel NULL pointer dereference, address: 0000000000000264
RIP: 0010:___ratelimit+0xc/0x1b0
pci_print_aer+0x141/0x360
aer_recover_work_func+0xb5/0x130
[8086:2020] is an Intel "Sky Lake-E DMI3 Registers" device that claims to
be a Root Port but does not advertise an AER Capability.
Add a NULL check in aer_ratelimit() to avoid the NULL pointer dereference.
Note that this also prevents ratelimiting these events from GHES.
[bhelgaas: add crash details to commit log] |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtl818x: Fix potential memory leaks in rtl8180_init_rx_ring()
In rtl8180_init_rx_ring(), memory is allocated for skb packets and DMA
allocations in a loop. When an allocation fails, the previously
successful allocations are not freed on exit.
Fix that by jumping to err_free_rings label on error, which calls
rtl8180_free_rx_ring() to free the allocations. Remove the free of
rx_ring in rtl8180_init_rx_ring() error path, and set the freed
priv->rx_buf entry to null, to avoid double free. |
| In the Linux kernel, the following vulnerability has been resolved:
backlight: led-bl: Add devlink to supplier LEDs
LED Backlight is a consumer of one or multiple LED class devices, but
devlink is currently unable to create correct supplier-producer links when
the supplier is a class device. It creates instead a link where the
supplier is the parent of the expected device.
One consequence is that removal order is not correctly enforced.
Issues happen for example with the following sections in a device tree
overlay:
// An LED driver chip
pca9632@62 {
compatible = "nxp,pca9632";
reg = <0x62>;
// ...
addon_led_pwm: led-pwm@3 {
reg = <3>;
label = "addon:led:pwm";
};
};
backlight-addon {
compatible = "led-backlight";
leds = <&addon_led_pwm>;
brightness-levels = <255>;
default-brightness-level = <255>;
};
In this example, the devlink should be created between the backlight-addon
(consumer) and the pca9632@62 (supplier). Instead it is created between the
backlight-addon (consumer) and the parent of the pca9632@62, which is
typically the I2C bus adapter.
On removal of the above overlay, the LED driver can be removed before the
backlight device, resulting in:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000010
...
Call trace:
led_put+0xe0/0x140
devm_led_release+0x6c/0x98
Another way to reproduce the bug without any device tree overlays is
unbinding the LED class device (pca9632@62) before unbinding the consumer
(backlight-addon):
echo 11-0062 >/sys/bus/i2c/drivers/leds-pca963x/unbind
echo ...backlight-dock >/sys/bus/platform/drivers/led-backlight/unbind
Fix by adding a devlink between the consuming led-backlight device and the
supplying LED device, as other drivers and subsystems do as well. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/vgem-fence: Fix potential deadlock on release
A timer that expires a vgem fence automatically in 10 seconds is now
released with timer_delete_sync() from fence->ops.release() called on last
dma_fence_put(). In some scenarios, it can run in IRQ context, which is
not safe unless TIMER_IRQSAFE is used. One potentially risky scenario was
demonstrated in Intel DRM CI trybot, BAT run on machine bat-adlp-6, while
working on new IGT subtests syncobj_timeline@stress-* as user space
replacements of some problematic test cases of a dma-fence-chain selftest
[1].
[117.004338] ================================
[117.004340] WARNING: inconsistent lock state
[117.004342] 6.17.0-rc7-CI_DRM_17270-g7644974e648c+ #1 Tainted: G S U
[117.004346] --------------------------------
[117.004347] inconsistent {HARDIRQ-ON-W} -> {IN-HARDIRQ-W} usage.
[117.004349] swapper/0/0 [HC1[1]:SC1[1]:HE0:SE0] takes:
[117.004352] ffff888138f86aa8 ((&fence->timer)){?.-.}-{0:0}, at: __timer_delete_sync+0x4b/0x190
[117.004361] {HARDIRQ-ON-W} state was registered at:
[117.004363] lock_acquire+0xc4/0x2e0
[117.004366] call_timer_fn+0x80/0x2a0
[117.004368] __run_timers+0x231/0x310
[117.004370] run_timer_softirq+0x76/0xe0
[117.004372] handle_softirqs+0xd4/0x4d0
[117.004375] __irq_exit_rcu+0x13f/0x160
[117.004377] irq_exit_rcu+0xe/0x20
[117.004379] sysvec_apic_timer_interrupt+0xa0/0xc0
[117.004382] asm_sysvec_apic_timer_interrupt+0x1b/0x20
[117.004385] cpuidle_enter_state+0x12b/0x8a0
[117.004388] cpuidle_enter+0x2e/0x50
[117.004393] call_cpuidle+0x22/0x60
[117.004395] do_idle+0x1fd/0x260
[117.004398] cpu_startup_entry+0x29/0x30
[117.004401] start_secondary+0x12d/0x160
[117.004404] common_startup_64+0x13e/0x141
[117.004407] irq event stamp: 2282669
[117.004409] hardirqs last enabled at (2282668): [<ffffffff8289db71>] _raw_spin_unlock_irqrestore+0x51/0x80
[117.004414] hardirqs last disabled at (2282669): [<ffffffff82882021>] sysvec_irq_work+0x11/0xc0
[117.004419] softirqs last enabled at (2254702): [<ffffffff8289fd00>] __do_softirq+0x10/0x18
[117.004423] softirqs last disabled at (2254725): [<ffffffff813d4ddf>] __irq_exit_rcu+0x13f/0x160
[117.004426]
other info that might help us debug this:
[117.004429] Possible unsafe locking scenario:
[117.004432] CPU0
[117.004433] ----
[117.004434] lock((&fence->timer));
[117.004436] <Interrupt>
[117.004438] lock((&fence->timer));
[117.004440]
*** DEADLOCK ***
[117.004443] 1 lock held by swapper/0/0:
[117.004445] #0: ffffc90000003d50 ((&fence->timer)){?.-.}-{0:0}, at: call_timer_fn+0x7a/0x2a0
[117.004450]
stack backtrace:
[117.004453] CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Tainted: G S U 6.17.0-rc7-CI_DRM_17270-g7644974e648c+ #1 PREEMPT(voluntary)
[117.004455] Tainted: [S]=CPU_OUT_OF_SPEC, [U]=USER
[117.004455] Hardware name: Intel Corporation Alder Lake Client Platform/AlderLake-P DDR4 RVP, BIOS RPLPFWI1.R00.4035.A00.2301200723 01/20/2023
[117.004456] Call Trace:
[117.004456] <IRQ>
[117.004457] dump_stack_lvl+0x91/0xf0
[117.004460] dump_stack+0x10/0x20
[117.004461] print_usage_bug.part.0+0x260/0x360
[117.004463] mark_lock+0x76e/0x9c0
[117.004465] ? register_lock_class+0x48/0x4a0
[117.004467] __lock_acquire+0xbc3/0x2860
[117.004469] lock_acquire+0xc4/0x2e0
[117.004470] ? __timer_delete_sync+0x4b/0x190
[117.004472] ? __timer_delete_sync+0x4b/0x190
[117.004473] __timer_delete_sync+0x68/0x190
[117.004474] ? __timer_delete_sync+0x4b/0x190
[117.004475] timer_delete_sync+0x10/0x20
[117.004476] vgem_fence_release+0x19/0x30 [vgem]
[117.004478] dma_fence_release+0xc1/0x3b0
[117.004480] ? dma_fence_release+0xa1/0x3b0
[117.004481] dma_fence_chain_release+0xe7/0x130
[117.004483] dma_fence_release+0xc1/0x3b0
[117.004484] ? _raw_spin_unlock_irqrestore+0x27/0x80
[117.004485] dma_fence_chain_irq_work+0x59/0x80
[117.004487] irq_work_single+0x75/0xa0
[117.004490] irq_work_r
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
block: Use RCU in blk_mq_[un]quiesce_tagset() instead of set->tag_list_lock
blk_mq_{add,del}_queue_tag_set() functions add and remove queues from
tagset, the functions make sure that tagset and queues are marked as
shared when two or more queues are attached to the same tagset.
Initially a tagset starts as unshared and when the number of added
queues reaches two, blk_mq_add_queue_tag_set() marks it as shared along
with all the queues attached to it. When the number of attached queues
drops to 1 blk_mq_del_queue_tag_set() need to mark both the tagset and
the remaining queues as unshared.
Both functions need to freeze current queues in tagset before setting on
unsetting BLK_MQ_F_TAG_QUEUE_SHARED flag. While doing so, both functions
hold set->tag_list_lock mutex, which makes sense as we do not want
queues to be added or deleted in the process. This used to work fine
until commit 98d81f0df70c ("nvme: use blk_mq_[un]quiesce_tagset")
made the nvme driver quiesce tagset instead of quiscing individual
queues. blk_mq_quiesce_tagset() does the job and quiesce the queues in
set->tag_list while holding set->tag_list_lock also.
This results in deadlock between two threads with these stacktraces:
__schedule+0x47c/0xbb0
? timerqueue_add+0x66/0xb0
schedule+0x1c/0xa0
schedule_preempt_disabled+0xa/0x10
__mutex_lock.constprop.0+0x271/0x600
blk_mq_quiesce_tagset+0x25/0xc0
nvme_dev_disable+0x9c/0x250
nvme_timeout+0x1fc/0x520
blk_mq_handle_expired+0x5c/0x90
bt_iter+0x7e/0x90
blk_mq_queue_tag_busy_iter+0x27e/0x550
? __blk_mq_complete_request_remote+0x10/0x10
? __blk_mq_complete_request_remote+0x10/0x10
? __call_rcu_common.constprop.0+0x1c0/0x210
blk_mq_timeout_work+0x12d/0x170
process_one_work+0x12e/0x2d0
worker_thread+0x288/0x3a0
? rescuer_thread+0x480/0x480
kthread+0xb8/0xe0
? kthread_park+0x80/0x80
ret_from_fork+0x2d/0x50
? kthread_park+0x80/0x80
ret_from_fork_asm+0x11/0x20
__schedule+0x47c/0xbb0
? xas_find+0x161/0x1a0
schedule+0x1c/0xa0
blk_mq_freeze_queue_wait+0x3d/0x70
? destroy_sched_domains_rcu+0x30/0x30
blk_mq_update_tag_set_shared+0x44/0x80
blk_mq_exit_queue+0x141/0x150
del_gendisk+0x25a/0x2d0
nvme_ns_remove+0xc9/0x170
nvme_remove_namespaces+0xc7/0x100
nvme_remove+0x62/0x150
pci_device_remove+0x23/0x60
device_release_driver_internal+0x159/0x200
unbind_store+0x99/0xa0
kernfs_fop_write_iter+0x112/0x1e0
vfs_write+0x2b1/0x3d0
ksys_write+0x4e/0xb0
do_syscall_64+0x5b/0x160
entry_SYSCALL_64_after_hwframe+0x4b/0x53
The top stacktrace is showing nvme_timeout() called to handle nvme
command timeout. timeout handler is trying to disable the controller and
as a first step, it needs to blk_mq_quiesce_tagset() to tell blk-mq not
to call queue callback handlers. The thread is stuck waiting for
set->tag_list_lock as it tries to walk the queues in set->tag_list.
The lock is held by the second thread in the bottom stack which is
waiting for one of queues to be frozen. The queue usage counter will
drop to zero after nvme_timeout() finishes, and this will not happen
because the thread will wait for this mutex forever.
Given that [un]quiescing queue is an operation that does not need to
sleep, update blk_mq_[un]quiesce_tagset() to use RCU instead of taking
set->tag_list_lock, update blk_mq_{add,del}_queue_tag_set() to use RCU
safe list operations. Also, delete INIT_LIST_HEAD(&q->tag_set_list)
in blk_mq_del_queue_tag_set() because we can not re-initialize it while
the list is being traversed under RCU. The deleted queue will not be
added/deleted to/from a tagset and it will be freed in blk_free_queue()
after the end of RCU grace period. |
| In the Linux kernel, the following vulnerability has been resolved:
irqchip/mchp-eic: Fix error code in mchp_eic_domain_alloc()
If irq_domain_translate_twocell() sets "hwirq" to >= MCHP_EIC_NIRQ (2) then
it results in an out of bounds access.
The code checks for invalid values, but doesn't set the error code. Return
-EINVAL in that case, instead of returning success. |
| In the Linux kernel, the following vulnerability has been resolved:
rtc: amlogic-a4: fix double free caused by devm
The clock obtained via devm_clk_get_enabled() is automatically managed
by devres and will be disabled and freed on driver detach. Manually
calling clk_disable_unprepare() in error path and remove function
causes double free.
Remove the redundant clk_disable_unprepare() calls from the probe
error path and aml_rtc_remove(), allowing the devm framework to
automatically manage the clock lifecycle. |
