| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: validate num_aces and harden ACE walk in smb_inherit_dacl()
smb_inherit_dacl() trusts the on-disk num_aces value from the parent
directory's DACL xattr and uses it to size a heap allocation:
aces_base = kmalloc(sizeof(struct smb_ace) * num_aces * 2, ...);
num_aces is a u16 read from le16_to_cpu(parent_pdacl->num_aces)
without checking that it is consistent with the declared pdacl_size.
An authenticated client whose parent directory's security.NTACL is
tampered (e.g. via offline xattr corruption or a concurrent path that
bypasses parse_dacl()) can present num_aces = 65535 with minimal
actual ACE data. This causes a ~8 MB allocation (not kzalloc, so
uninitialized) that the subsequent loop only partially populates, and
may also overflow the three-way size_t multiply on 32-bit kernels.
Additionally, the ACE walk loop uses the weaker
offsetof(struct smb_ace, access_req) minimum size check rather than
the minimum valid on-wire ACE size, and does not reject ACEs whose
declared size is below the minimum.
Reproduced on UML + KASAN + LOCKDEP against the real ksmbd code path.
A legitimate mount.cifs client creates a parent directory over SMB
(ksmbd writes a valid security.NTACL xattr), then the NTACL blob on
the backing filesystem is rewritten to set num_aces = 0xFFFF while
keeping the posix_acl_hash bytes intact so ksmbd_vfs_get_sd_xattr()'s
hash check still passes. A subsequent SMB2 CREATE of a child under
that parent drives smb2_open() into smb_inherit_dacl() (share has
"vfs objects = acl_xattr" set), which fails the page allocator:
WARNING: mm/page_alloc.c:5226 at __alloc_frozen_pages_noprof+0x46c/0x9c0
Workqueue: ksmbd-io handle_ksmbd_work
__alloc_frozen_pages_noprof+0x46c/0x9c0
___kmalloc_large_node+0x68/0x130
__kmalloc_large_node_noprof+0x24/0x70
__kmalloc_noprof+0x4c9/0x690
smb_inherit_dacl+0x394/0x2430
smb2_open+0x595d/0xabe0
handle_ksmbd_work+0x3d3/0x1140
With the patch applied the added guard rejects the tampered value
with -EINVAL before any large allocation runs, smb2_open() falls back
to smb2_create_sd_buffer(), and the child is created with a default
SD. No warning, no splat.
Fix by:
1. Validating num_aces against pdacl_size using the same formula
applied in parse_dacl().
2. Replacing the raw kmalloc(sizeof * num_aces * 2) with
kmalloc_array(num_aces * 2, sizeof(...)) for overflow-safe
allocation.
3. Tightening the per-ACE loop guard to require the minimum valid
ACE size (offsetof(smb_ace, sid) + CIFS_SID_BASE_SIZE) and
rejecting under-sized ACEs, matching the hardening in
smb_check_perm_dacl() and parse_dacl().
v1 -> v2:
- Replace the synthetic test-module splat in the changelog with a
real-path UML + KASAN reproduction driven through mount.cifs and
SMB2 CREATE; Namjae flagged the kcifs3_test_inherit_dacl_old name
in v1 since it does not exist in ksmbd.
- Drop the commit-hash citation from the code comment per Namjae's
review; keep the parse_dacl() pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: af_alg - limit RX SG extraction by receive buffer budget
Make af_alg_get_rsgl() limit each RX scatterlist extraction to the
remaining receive buffer budget.
af_alg_get_rsgl() currently uses af_alg_readable() only as a gate
before extracting data into the RX scatterlist. Limit each extraction
to the remaining af_alg_rcvbuf(sk) budget so that receive-side
accounting matches the amount of data attached to the request.
If skcipher cannot obtain enough RX space for at least one chunk while
more data remains to be processed, reject the recvmsg call instead of
rounding the request length down to zero. |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: hold dev ref until after transport_finish NF_HOOK
After async crypto completes, xfrm_input_resume() calls dev_put()
immediately on re-entry before the skb reaches transport_finish.
The skb->dev pointer is then used inside NF_HOOK and its okfn,
which can race with device teardown.
Remove the dev_put from the async resumption entry and instead
drop the reference after the NF_HOOK call in transport_finish,
using a saved device pointer since NF_HOOK may consume the skb.
This covers NF_DROP, NF_QUEUE and NF_STOLEN paths that skip
the okfn.
For non-transport exits (decaps, gro, drop) and secondary
async return points, release the reference inline when
async is set. |
| In the Linux kernel, the following vulnerability has been resolved:
rxrpc: proc: size address buffers for %pISpc output
The AF_RXRPC procfs helpers format local and remote socket addresses into
fixed 50-byte stack buffers with "%pISpc".
That is too small for the longest current-tree IPv6-with-port form the
formatter can produce. In lib/vsprintf.c, the compressed IPv6 path uses a
dotted-quad tail not only for v4mapped addresses, but also for ISATAP
addresses via ipv6_addr_is_isatap().
As a result, a case such as
[ffff:ffff:ffff:ffff:0:5efe:255.255.255.255]:65535
is possible with the current formatter. That is 50 visible characters, so
51 bytes including the trailing NUL, which does not fit in the existing
char[50] buffers used by net/rxrpc/proc.c.
Size the buffers from the formatter's maximum textual form and switch the
call sites to scnprintf().
Changes since v1:
- correct the changelog to cite the actual maximum current-tree case
explicitly
- frame the proof around the ISATAP formatting path instead of the earlier
mapped-v4 example |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: f_hid: don't call cdev_init while cdev in use
When calling unbind, then bind again, cdev_init reinitialized the cdev,
even though there may still be references to it. That's the case when
the /dev/hidg* device is still opened. This obviously unsafe behavior
like oopes.
This fixes this by using cdev_alloc to put the cdev on the heap. That
way, we can simply allocate a new one in hidg_bind. |
| In the Linux kernel, the following vulnerability has been resolved:
media: verisilicon: Fix kernel panic due to __initconst misuse
Fix a kernel panic when probing the driver as a module:
Unable to handle kernel paging request at virtual address
ffffd9c18eb05000
of_find_matching_node_and_match+0x5c/0x1a0
hantro_probe+0x2f4/0x7d0 [hantro_vpu]
The imx8mq_vpu_shared_resources array is referenced by variant
structures through their shared_devices field. When built as a
module, __initconst causes this data to be freed after module
init, but it's later accessed during probe, causing a page fault.
The imx8mq_vpu_shared_resources is referenced from non-init code,
so keeping __initconst or __initconst_or_module here is wrong.
Drop the __initconst annotation and let it live in the normal .rodata
section.
A bug of __initconst called from regular non-init probe code
leading to bugs during probe deferrals or during unbind-bind cycles. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: spi-dw-dma: fix print error log when wait finish transaction
If an error occurs, the device may not have a current message. In this
case, the system will crash.
In this case, it's better to use dev from the struct ctlr (struct spi_controller*). |
| In the Linux kernel, the following vulnerability has been resolved:
nvmet: move async event work off nvmet-wq
For target nvmet_ctrl_free() flushes ctrl->async_event_work.
If nvmet_ctrl_free() runs on nvmet-wq, the flush re-enters workqueue
completion for the same worker:-
A. Async event work queued on nvmet-wq (prior to disconnect):
nvmet_execute_async_event()
queue_work(nvmet_wq, &ctrl->async_event_work)
nvmet_add_async_event()
queue_work(nvmet_wq, &ctrl->async_event_work)
B. Full pre-work chain (RDMA CM path):
nvmet_rdma_cm_handler()
nvmet_rdma_queue_disconnect()
__nvmet_rdma_queue_disconnect()
queue_work(nvmet_wq, &queue->release_work)
process_one_work()
lock((wq_completion)nvmet-wq) <--------- 1st
nvmet_rdma_release_queue_work()
C. Recursive path (same worker):
nvmet_rdma_release_queue_work()
nvmet_rdma_free_queue()
nvmet_sq_destroy()
nvmet_ctrl_put()
nvmet_ctrl_free()
flush_work(&ctrl->async_event_work)
__flush_work()
touch_wq_lockdep_map()
lock((wq_completion)nvmet-wq) <--------- 2nd
Lockdep splat:
============================================
WARNING: possible recursive locking detected
6.19.0-rc3nvme+ #14 Tainted: G N
--------------------------------------------
kworker/u192:42/44933 is trying to acquire lock:
ffff888118a00948 ((wq_completion)nvmet-wq){+.+.}-{0:0}, at: touch_wq_lockdep_map+0x26/0x90
but task is already holding lock:
ffff888118a00948 ((wq_completion)nvmet-wq){+.+.}-{0:0}, at: process_one_work+0x53e/0x660
3 locks held by kworker/u192:42/44933:
#0: ffff888118a00948 ((wq_completion)nvmet-wq){+.+.}-{0:0}, at: process_one_work+0x53e/0x660
#1: ffffc9000e6cbe28 ((work_completion)(&queue->release_work)){+.+.}-{0:0}, at: process_one_work+0x1c5/0x660
#2: ffffffff82d4db60 (rcu_read_lock){....}-{1:3}, at: __flush_work+0x62/0x530
Workqueue: nvmet-wq nvmet_rdma_release_queue_work [nvmet_rdma]
Call Trace:
__flush_work+0x268/0x530
nvmet_ctrl_free+0x140/0x310 [nvmet]
nvmet_cq_put+0x74/0x90 [nvmet]
nvmet_rdma_free_queue+0x23/0xe0 [nvmet_rdma]
nvmet_rdma_release_queue_work+0x19/0x50 [nvmet_rdma]
process_one_work+0x206/0x660
worker_thread+0x184/0x320
kthread+0x10c/0x240
ret_from_fork+0x319/0x390
Move async event work to a dedicated nvmet-aen-wq to avoid reentrant
flush on nvmet-wq. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv4: nexthop: allocate skb dynamically in rtm_get_nexthop()
When querying a nexthop object via RTM_GETNEXTHOP, the kernel currently
allocates a fixed-size skb using NLMSG_GOODSIZE. While sufficient for
single nexthops and small Equal-Cost Multi-Path groups, this fixed
allocation fails for large nexthop groups like 512 nexthops.
This results in the following warning splat:
WARNING: net/ipv4/nexthop.c:3395 at rtm_get_nexthop+0x176/0x1c0, CPU#20: rep/4608
[...]
RIP: 0010:rtm_get_nexthop (net/ipv4/nexthop.c:3395)
[...]
Call Trace:
<TASK>
rtnetlink_rcv_msg (net/core/rtnetlink.c:6989)
netlink_rcv_skb (net/netlink/af_netlink.c:2550)
netlink_unicast (net/netlink/af_netlink.c:1319 net/netlink/af_netlink.c:1344)
netlink_sendmsg (net/netlink/af_netlink.c:1894)
____sys_sendmsg (net/socket.c:721 net/socket.c:736 net/socket.c:2585)
___sys_sendmsg (net/socket.c:2641)
__sys_sendmsg (net/socket.c:2671)
do_syscall_64 (arch/x86/entry/syscall_64.c:63 arch/x86/entry/syscall_64.c:94)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)
</TASK>
Fix this by allocating the size dynamically using nh_nlmsg_size() and
using nlmsg_new(), this is consistent with nexthop_notify() behavior. In
addition, adjust nh_nlmsg_size_grp() so it calculates the size needed
based on flags passed. While at it, also add the size of NHA_FDB for
nexthop group size calculation as it was missing too.
This cannot be reproduced via iproute2 as the group size is currently
limited and the command fails as follows:
addattr_l ERROR: message exceeded bound of 1048 |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: prevent immediate PASID reuse case
PASID resue could cause interrupt issue when process
immediately runs into hw state left by previous
process exited with the same PASID, it's possible that
page faults are still pending in the IH ring buffer when
the process exits and frees up its PASID. To prevent the
case, it uses idr cyclic allocator same as kernel pid's.
(cherry picked from commit 8f1de51f49be692de137c8525106e0fce2d1912d) |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: use volume UUID in FS_OBJECT_ID_INFORMATION
Use sb->s_uuid for a proper volume identifier as the primary choice.
For filesystems that do not provide a UUID, fall back to stfs.f_fsid
obtained from vfs_statfs(). |
| In the Linux kernel, the following vulnerability has been resolved:
ip_tunnel: adapt iptunnel_xmit_stats() to NETDEV_PCPU_STAT_DSTATS
Blamed commits forgot that vxlan/geneve use udp_tunnel[6]_xmit_skb() which
call iptunnel_xmit_stats().
iptunnel_xmit_stats() was assuming tunnels were only using
NETDEV_PCPU_STAT_TSTATS.
@syncp offset in pcpu_sw_netstats and pcpu_dstats is different.
32bit kernels would either have corruptions or freezes if the syncp
sequence was overwritten.
This patch also moves pcpu_stat_type closer to dev->{t,d}stats to avoid
a potential cache line miss since iptunnel_xmit_stats() needs to read it. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_tables: clone set on flush only
Syzbot with fault injection triggered a failing memory allocation with
GFP_KERNEL which results in a WARN splat:
iter.err
WARNING: net/netfilter/nf_tables_api.c:845 at nft_map_deactivate+0x34e/0x3c0 net/netfilter/nf_tables_api.c:845, CPU#0: syz.0.17/5992
Modules linked in:
CPU: 0 UID: 0 PID: 5992 Comm: syz.0.17 Not tainted syzkaller #0 PREEMPT(full)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 02/12/2026
RIP: 0010:nft_map_deactivate+0x34e/0x3c0 net/netfilter/nf_tables_api.c:845
Code: 8b 05 86 5a 4e 09 48 3b 84 24 a0 00 00 00 75 62 48 8d 65 d8 5b 41 5c 41 5d 41 5e 41 5f 5d c3 cc cc cc cc cc e8 63 6d fa f7 90 <0f> 0b 90 43
+80 7c 35 00 00 0f 85 23 fe ff ff e9 26 fe ff ff 89 d9
RSP: 0018:ffffc900045af780 EFLAGS: 00010293
RAX: ffffffff89ca45bd RBX: 00000000fffffff4 RCX: ffff888028111e40
RDX: 0000000000000000 RSI: 00000000fffffff4 RDI: 0000000000000000
RBP: ffffc900045af870 R08: 0000000000400dc0 R09: 00000000ffffffff
R10: dffffc0000000000 R11: fffffbfff1d141db R12: ffffc900045af7e0
R13: 1ffff920008b5f24 R14: dffffc0000000000 R15: ffffc900045af920
FS: 000055557a6a5500(0000) GS:ffff888125496000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fb5ea271fc0 CR3: 000000003269e000 CR4: 00000000003526f0
Call Trace:
<TASK>
__nft_release_table+0xceb/0x11f0 net/netfilter/nf_tables_api.c:12115
nft_rcv_nl_event+0xc25/0xdb0 net/netfilter/nf_tables_api.c:12187
notifier_call_chain+0x19d/0x3a0 kernel/notifier.c:85
blocking_notifier_call_chain+0x6a/0x90 kernel/notifier.c:380
netlink_release+0x123b/0x1ad0 net/netlink/af_netlink.c:761
__sock_release net/socket.c:662 [inline]
sock_close+0xc3/0x240 net/socket.c:1455
Restrict set clone to the flush set command in the preparation phase.
Add NFT_ITER_UPDATE_CLONE and use it for this purpose, update the rbtree
and pipapo backends to only clone the set when this iteration type is
used.
As for the existing NFT_ITER_UPDATE type, update the pipapo backend to
use the existing set clone if available, otherwise use the existing set
representation. After this update, there is no need to clone a set that
is being deleted, this includes bound anonymous set.
An alternative approach to NFT_ITER_UPDATE_CLONE is to add a .clone
interface and call it from the flush set path. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf, arm64: Force 8-byte alignment for JIT buffer to prevent atomic tearing
struct bpf_plt contains a u64 target field. Currently, the BPF JIT
allocator requests an alignment of 4 bytes (sizeof(u32)) for the JIT
buffer.
Because the base address of the JIT buffer can be 4-byte aligned (e.g.,
ending in 0x4 or 0xc), the relative padding logic in build_plt() fails
to ensure that target lands on an 8-byte boundary.
This leads to two issues:
1. UBSAN reports misaligned-access warnings when dereferencing the
structure.
2. More critically, target is updated concurrently via WRITE_ONCE() in
bpf_arch_text_poke() while the JIT'd code executes ldr. On arm64,
64-bit loads/stores are only guaranteed to be single-copy atomic if
they are 64-bit aligned. A misaligned target risks a torn read,
causing the JIT to jump to a corrupted address.
Fix this by increasing the allocation alignment requirement to 8 bytes
(sizeof(u64)) in bpf_jit_binary_pack_alloc(). This anchors the base of
the JIT buffer to an 8-byte boundary, allowing the relative padding math
in build_plt() to correctly align the target field. |
| In the Linux kernel, the following vulnerability has been resolved:
ice: change XDP RxQ frag_size from DMA write length to xdp.frame_sz
The only user of frag_size field in XDP RxQ info is
bpf_xdp_frags_increase_tail(). It clearly expects whole buff size instead
of DMA write size. Different assumptions in ice driver configuration lead
to negative tailroom.
This allows to trigger kernel panic, when using
XDP_ADJUST_TAIL_GROW_MULTI_BUFF xskxceiver test and changing packet size to
6912 and the requested offset to a huge value, e.g.
XSK_UMEM__MAX_FRAME_SIZE * 100.
Due to other quirks of the ZC configuration in ice, panic is not observed
in ZC mode, but tailroom growing still fails when it should not.
Use fill queue buffer truesize instead of DMA write size in XDP RxQ info.
Fix ZC mode too by using the new helper. |
| In the Linux kernel, the following vulnerability has been resolved:
sched/deadline: Fix missing ENQUEUE_REPLENISH during PI de-boosting
Running stress-ng --schedpolicy 0 on an RT kernel on a big machine
might lead to the following WARNINGs (edited).
sched: DL de-boosted task PID 22725: REPLENISH flag missing
WARNING: CPU: 93 PID: 0 at kernel/sched/deadline.c:239 dequeue_task_dl+0x15c/0x1f8
... (running_bw underflow)
Call trace:
dequeue_task_dl+0x15c/0x1f8 (P)
dequeue_task+0x80/0x168
deactivate_task+0x24/0x50
push_dl_task+0x264/0x2e0
dl_task_timer+0x1b0/0x228
__hrtimer_run_queues+0x188/0x378
hrtimer_interrupt+0xfc/0x260
...
The problem is that when a SCHED_DEADLINE task (lock holder) is
changed to a lower priority class via sched_setscheduler(), it may
fail to properly inherit the parameters of potential DEADLINE donors
if it didn't already inherit them in the past (shorter deadline than
donor's at that time). This might lead to bandwidth accounting
corruption, as enqueue_task_dl() won't recognize the lock holder as
boosted.
The scenario occurs when:
1. A DEADLINE task (donor) blocks on a PI mutex held by another
DEADLINE task (holder), but the holder doesn't inherit parameters
(e.g., it already has a shorter deadline)
2. sched_setscheduler() changes the holder from DEADLINE to a lower
class while still holding the mutex
3. The holder should now inherit DEADLINE parameters from the donor
and be enqueued with ENQUEUE_REPLENISH, but this doesn't happen
Fix the issue by introducing __setscheduler_dl_pi(), which detects when
a DEADLINE (proper or boosted) task gets setscheduled to a lower
priority class. In case, the function makes the task inherit DEADLINE
parameters of the donoer (pi_se) and sets ENQUEUE_REPLENISH flag to
ensure proper bandwidth accounting during the next enqueue operation. |
| In the Linux kernel, the following vulnerability has been resolved:
io_uring/rw: free potentially allocated iovec on cache put failure
If a read/write request goes through io_req_rw_cleanup() and has an
allocated iovec attached and fails to put to the rw_cache, then it may
end up with an unaccounted iovec pointer. Have io_rw_recycle() return
whether it recycled the request or not, and use that to gauge whether to
free a potential iovec or not. |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: secure_seq: add back ports to TS offset
This reverts 28ee1b746f49 ("secure_seq: downgrade to per-host timestamp offsets")
tcp_tw_recycle went away in 2017.
Zhouyan Deng reported off-path TCP source port leakage via
SYN cookie side-channel that can be fixed in multiple ways.
One of them is to bring back TCP ports in TS offset randomization.
As a bonus, we perform a single siphash() computation
to provide both an ISN and a TS offset. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: reject new transactions if the fs is fully read-only
[BUG]
There is a bug report where a heavily fuzzed fs is mounted with all
rescue mount options, which leads to the following warnings during
unmount:
BTRFS: Transaction aborted (error -22)
Modules linked in:
CPU: 0 UID: 0 PID: 9758 Comm: repro.out Not tainted
6.19.0-rc5-00002-gb71e635feefc #7 PREEMPT(full)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014
RIP: 0010:find_free_extent_update_loop fs/btrfs/extent-tree.c:4208 [inline]
RIP: 0010:find_free_extent+0x52f0/0x5d20 fs/btrfs/extent-tree.c:4611
Call Trace:
<TASK>
btrfs_reserve_extent+0x2cd/0x790 fs/btrfs/extent-tree.c:4705
btrfs_alloc_tree_block+0x1e1/0x10e0 fs/btrfs/extent-tree.c:5157
btrfs_force_cow_block+0x578/0x2410 fs/btrfs/ctree.c:517
btrfs_cow_block+0x3c4/0xa80 fs/btrfs/ctree.c:708
btrfs_search_slot+0xcad/0x2b50 fs/btrfs/ctree.c:2130
btrfs_truncate_inode_items+0x45d/0x2350 fs/btrfs/inode-item.c:499
btrfs_evict_inode+0x923/0xe70 fs/btrfs/inode.c:5628
evict+0x5f4/0xae0 fs/inode.c:837
__dentry_kill+0x209/0x660 fs/dcache.c:670
finish_dput+0xc9/0x480 fs/dcache.c:879
shrink_dcache_for_umount+0xa0/0x170 fs/dcache.c:1661
generic_shutdown_super+0x67/0x2c0 fs/super.c:621
kill_anon_super+0x3b/0x70 fs/super.c:1289
btrfs_kill_super+0x41/0x50 fs/btrfs/super.c:2127
deactivate_locked_super+0xbc/0x130 fs/super.c:474
cleanup_mnt+0x425/0x4c0 fs/namespace.c:1318
task_work_run+0x1d4/0x260 kernel/task_work.c:233
exit_task_work include/linux/task_work.h:40 [inline]
do_exit+0x694/0x22f0 kernel/exit.c:971
do_group_exit+0x21c/0x2d0 kernel/exit.c:1112
__do_sys_exit_group kernel/exit.c:1123 [inline]
__se_sys_exit_group kernel/exit.c:1121 [inline]
__x64_sys_exit_group+0x3f/0x40 kernel/exit.c:1121
x64_sys_call+0x2210/0x2210 arch/x86/include/generated/asm/syscalls_64.h:232
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xe8/0xf80 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x44f639
Code: Unable to access opcode bytes at 0x44f60f.
RSP: 002b:00007ffc15c4e088 EFLAGS: 00000246 ORIG_RAX: 00000000000000e7
RAX: ffffffffffffffda RBX: 00000000004c32f0 RCX: 000000000044f639
RDX: 000000000000003c RSI: 00000000000000e7 RDI: 0000000000000001
RBP: 0000000000000001 R08: ffffffffffffffc0 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00000000004c32f0
R13: 0000000000000001 R14: 0000000000000000 R15: 0000000000000001
</TASK>
Since rescue mount options will mark the full fs read-only, there should
be no new transaction triggered.
But during unmount we will evict all inodes, which can trigger a new
transaction, and triggers warnings on a heavily corrupted fs.
[CAUSE]
Btrfs allows new transaction even on a read-only fs, this is to allow
log replay happen even on read-only mounts, just like what ext4/xfs do.
However with rescue mount options, the fs is fully read-only and cannot
be remounted read-write, thus in that case we should also reject any new
transactions.
[FIX]
If we find the fs has rescue mount options, we should treat the fs as
error, so that no new transaction can be started. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/pm: Disable MMIO access during SMU Mode 1 reset
During Mode 1 reset, the ASIC undergoes a reset cycle and becomes
temporarily inaccessible via PCIe. Any attempt to access MMIO registers
during this window (e.g., from interrupt handlers or other driver threads)
can result in uncompleted PCIe transactions, leading to NMI panics or
system hangs.
To prevent this, set the `no_hw_access` flag to true immediately after
triggering the reset. This signals other driver components to skip
register accesses while the device is offline.
A memory barrier `smp_mb()` is added to ensure the flag update is
globally visible to all cores before the driver enters the sleep/wait
state.
(cherry picked from commit 7edb503fe4b6d67f47d8bb0dfafb8e699bb0f8a4) |
