| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: thunderbolt: Fix frags[] overflow by bounding frame_count
tbnet_poll() assembles a multi-frame ThunderboltIP packet into one skb. The
first frame goes into the skb linear area and every further frame is added as
a page fragment.
skb_add_rx_frag(skb, skb_shinfo(skb)->nr_frags,
page, hdr_size, frame_size,
TBNET_RX_PAGE_SIZE - hdr_size);
A packet of frame_count frames therefore ends up with frame_count - 1
fragments. tbnet_check_frame() only bounds the peer supplied frame_count to
TBNET_RING_SIZE / 4 (64), which is far above MAX_SKB_FRAGS (17 by default). A
peer that sends a packet of 19 or more small frames pushes nr_frags past
MAX_SKB_FRAGS, so skb_add_rx_frag() writes past skb_shinfo()->frags[] and
corrupts memory after the shared info.
Tighten the start of packet bound to MAX_SKB_FRAGS + 1 so a packet can never
produce more fragments than frags[] can hold. This matches the recent skb
frags overflow fixes in other receive paths, for example f0813bcd2d9d ("net:
wwan: t7xx: fix potential skb->frags overflow in RX path") and 600dc40554dc
("net: usb: cdc-phonet: fix skb frags[] overflow in rx_complete()"). |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: tegra: Fix burst size calculation
Currently, the Tegra GPC DMA hardware requires the transfer length to
be a multiple of the max burst size configured for the channel. When a
client requests a transfer where the length is not evenly divisible by
the configured max burst size, the DMA hangs with partial burst at
the end.
Fix this by reducing the burst size to the largest power-of-2 value
that evenly divides the transfer length. For example, a 40-byte
transfer with a 16-byte max burst will now use an 8-byte burst
(40 / 8 = 5 complete bursts) instead of causing a hang.
This issue was observed with the PL011 UART driver where TX DMA
transfers of arbitrary lengths were stuck. |
| In the Linux kernel, the following vulnerability has been resolved:
platform/x86: ISST: Restore SST-PP control to all domains
The SST-PP control offset is only restored to power domain 0 after
resume. During suspend, control values are read and stored for all
power domains.
Use pd_info->sst_base instead of power_domain_info->sst_base, which
only points to power domain 0 base address. |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: xfrm_interface: require CAP_NET_ADMIN in the device netns for changelink
xfrmi_changelink() operates on at most two netns, dev_net(dev) and the
interface link netns xi->net. They differ once the device is created in
or moved to a netns other than the one the request runs in. The rtnl
changelink path checks CAP_NET_ADMIN only against dev_net(dev), so a
caller privileged there but not in xi->net can rewrite an interface that
lives in xi->net.
Gate xfrmi_changelink() on rtnl_dev_link_net_capable() at its top,
before any attribute is parsed. |
| In the Linux kernel, the following vulnerability has been resolved:
tpm: Make the TPM character devices non-seekable
The TPM character devices expose a sequential command/response
interface, but their open handlers leave FMODE_PREAD and FMODE_PWRITE
enabled.
After a command leaves a response pending, pread(fd, buf, 16, 0x1400)
passes 0x1400 as *off to tpm_common_read(). The transfer length is
bounded by response_length, but the offset is used unchecked when
forming data_buffer + *off. A sufficiently large offset therefore causes
an out-of-bounds heap read through copy_to_user() and, if the copy
succeeds, an out-of-bounds zero-write through the following memset().
Positional I/O does not provide coherent semantics for this interface.
An arbitrary pread offset cannot represent how much of a response has
been consumed sequentially. The write callback always stores a command
at the start of data_buffer, while pwrite() does not update file->f_pos
and can leave the sequential read cursor stale.
Call nonseekable_open() from both open handlers. This removes
FMODE_PREAD and FMODE_PWRITE, causing positional reads and writes to
fail with -ESPIPE before reaching the TPM callbacks, and explicitly
marks the files non-seekable. Normal read() and write() continue to use
the existing sequential f_pos cursor, leaving the response state machine
unchanged.
Tested on Linux 6.12 with KASAN and a swtpm TPM2 device:
- sequential partial reads returned the complete response
- pread() and preadv() with offset 0x1400 returned -ESPIPE
- pwrite() and pwritev() with offset zero returned -ESPIPE
- the pending response remained intact after the rejected operations
- a subsequent normal command/response cycle completed normally
- no KASAN report was produced. |
| In the Linux kernel, the following vulnerability has been resolved:
can: isotp: use unconditional synchronize_rcu() in isotp_release()
isotp_notify() unregisters the (RCU) CAN filters via can_rx_unregister()
and clears so->bound without waiting for a grace period. isotp_release()
uses so->bound to decide whether it needs to call synchronize_rcu()
before cancelling so->rxtimer, so when NETDEV_UNREGISTER runs first it
skips that synchronize_rcu() and can cancel the timer while an
in-flight isotp_rcv() is still executing and about to re-arm it via
isotp_send_fc(), leading to a use-after-free timer callback on the
freed socket.
sakisho-bot remarked a problem with rtnl_lock held in isotp_notify(),
therefore make isotp_release() always call synchronize_rcu() before
cancelling the timers, regardless of so->bound. This still closes the
original race (isotp_notify() clearing so->bound without waiting for
in-flight isotp_rcv() callers before isotp_release() cancels the RX
timer) without adding any RCU wait to the netdevice notifier path. |
| In the Linux kernel, the following vulnerability has been resolved:
can: isotp: fix use-after-free race with concurrent NETDEV_UNREGISTER
isotp_release() looked up the bound network device via dev_get_by_index()
using the stored ifindex. During device unregistration the device is
unlisted from the ifindex hash before the NETDEV_UNREGISTER notifier
chain runs, so a concurrent isotp_release() could find no device, skip
can_rx_unregister() entirely, and still proceed to free the socket.
Since isotp_release() had already removed itself from the isotp
notifier list at that point, isotp_notify() would never get a chance to
clean up either, leaving a stale CAN filter that keeps pointing at the
freed socket.
Fix this the same way raw.c already does: hold a tracked reference to
the bound net_device in the socket (so->dev/so->dev_tracker) from
bind() onward instead of re-resolving it from the ifindex, and
serialize bind()/release() with rtnl_lock() so that so->dev is always
consistent with what the NETDEV_UNREGISTER notifier sees. so->dev
stays valid regardless of ifindex-hash unlisting, and is only ever
cleared by whichever of isotp_release()/isotp_notify() gets there
first, so the filter is always removed exactly once.
isotp_bind() now rejects a (re)bind with -EAGAIN while so->[tx|rx].state
isn't ISOTP_IDLE yet, so a timer left running by a prior
NETDEV_UNREGISTER can't act on a newly bound so->ifindex. Both checks
share the same lock_sock() section, so there is no window in which a
concurrent isotp_notify() clearing so->bound could be missed. |
| In the Linux kernel, the following vulnerability has been resolved:
can: isotp: serialize TX state transitions under so->rx_lock
The TX state machine (so->tx.state) is driven from three contexts:
sendmsg() claiming and progressing a transfer, the RX path consuming
Flow Control/echo frames, and two hrtimers timing out a stalled
transfer. Mixing a lock-free cmpxchg() claim in sendmsg() with
hrtimer_cancel() calls made under so->rx_lock elsewhere left windows
where a frame or timer callback could act on a state that had already
moved on, corrupting an unrelated transfer.
so->rx_lock now covers the full lifecycle of a TX claim: sendmsg()
takes it to check so->tx.state is ISOTP_IDLE, switch it to
ISOTP_SENDING, bump so->tx_gen and drain the previous transfer's
timers - all as one critical section. isotp_rcv_fc()/isotp_rcv_cf()
already run under this lock via isotp_rcv(), and isotp_rcv_echo() now
takes it itself, so none of them can ever observe a transfer mid-claim.
This also means a transfer can no longer be handed to sendmsg()'s
cleanup paths (signal or send error) while another thread is
concurrently claiming or finishing it, so those paths can cancel
timers and reset the state unconditionally.
isotp_release() claims the socket the same way, so a racing sendmsg()
sees a consistent ISOTP_SHUTDOWN and skips arming its timer or sending.
Only the hrtimer callbacks stay outside so->rx_lock, since they run
under so->rx_lock's cancellation elsewhere and taking it themselves
would deadlock. so->tx_gen lets them recognize whether the transfer
they timed out is still the one currently active, so they don't
report an error against a transfer that has since completed or been
superseded. |
| In the Linux kernel, the following vulnerability has been resolved:
can: bcm: defer rx_op deallocation to workqueue to fix thrtimer UAF
Commit f1b4e32aca08 ("can: bcm: use call_rcu() instead of costly
synchronize_rcu()") replaced synchronize_rcu() in bcm_delete_rx_op()
with call_rcu() and introduced the RX_NO_AUTOTIMER flag.
However, this flag check was omitted for thrtimer in the packet rx
fast-path. During BCM RX operation teardown, a concurrent RCU reader
(bcm_rx_handler) can race and re-arm thrtimer via
bcm_rx_update_and_send() after call_rcu() has been scheduled. Once
the RCU grace period elapses, bcm_op is freed. The subsequently
firing thrtimer then dereferences the deallocated op, causing a UAF.
Adding flag checks to the rx fast-path (bcm_rx_update_and_send) does not
fully close the TOCTOU race and introduces latency for every CAN frame.
Conversely, calling hrtimer_cancel() directly inside the RCU callback
(softirq context) is fatal as hrtimer_cancel() can sleep, triggering
a "scheduling while atomic" panic.
Resolve this by deferring the timer cancellation and memory free to a
dedicated unbound workqueue (bcm_wq). The RCU callback now queues a
work item to bcm_wq, which safely cancels both timers and deallocates
memory in sleepable process context. A dedicated workqueue is used to
prevent system-wide WQ saturation and is cleanly flushed/destroyed
on module unload to avoid rmmod page faults.
Since the deferred work can now outlive the calling context by an
unbounded amount, also take a reference on op->sk when it is assigned
and drop it only once the deferred work has cancelled both timers, so a
socket can no longer be freed out from under a still-armed timer whose
callback (bcm_send_to_user()) dereferences op->sk. |
| In the Linux kernel, the following vulnerability has been resolved:
can: bcm: fix lockless bound/ifindex race and silent RX_SETUP failure
bcm_sendmsg() reads bo->ifindex and checks bo->bound before taking
lock_sock(), while bcm_notify(), bcm_connect() and bcm_release() all
mutate both fields under that same lock. Because the lockless reads
and the locked writes are unordered with respect to each other, a
racing bcm_notify() (device unregister) or bcm_connect() (concurrent
bind on another thread sharing the socket) can make bcm_sendmsg()
observe an inconsistent combination, e.g. a stale bound=1 together
with the now-cleared ifindex=0, silently turning a socket bound to a
specific CAN interface into one that also matches "any" interface.
Keep the lockless bo->bound check purely as a fast-path reject, and
move the ifindex read (and a bo->bound re-check) into the locked
section, where every writer already serializes. This removes the
possibility of observing the two fields torn against each other,
rather than trying to fix it with more READ_ONCE()/WRITE_ONCE() pairs
on two independently updated fields. Annotate the now-purely-lockless
bo->bound accesses consistently across all its write sites.
Also fix bcm_rx_setup() silently returning success when the target
device disappears concurrently instead of reporting -ENODEV, so a
broken RX op is no longer left registered as if it had succeeded. |
| In the Linux kernel, the following vulnerability has been resolved:
can: bcm: add locking when updating filter and timer values
KCSAN detected a simultaneous access to timer values that can be
overwritten in bcm_rx_setup() when updating timer and filter content
while bcm_rx_handler(), bcm_rx_timeout_handler() or bcm_rx_thr_handler()
run concurrently on incoming CAN traffic.
Protect the timer (ival1/ival2/kt_ival1/kt_ival2/kt_lastmsg) and filter
(nframes/flags/frames/last_frames) updates in bcm_rx_setup() with a new
per-op bcm_rx_update_lock, taken with the matching scope in the RX
handlers. memcpy_from_msg() is staged into a temporary buffer before the
lock is taken, since it can sleep and must not run under a spinlock.
hrtimer_cancel() is always called without bcm_rx_update_lock held, since
bcm_rx_timeout_handler()/bcm_rx_thr_handler() take the same lock and a
running callback would otherwise deadlock against the canceller.
Also close a related race: bcm_rx_setup() cleared the RTR flag in the
stored reply frame's can_id as a separate, unprotected step after the
frame content was already installed, so a concurrent bcm_rx_handler()
could transmit a stale reply with CAN_RTR_FLAG still set. Fold that
normalization into the initial frame preparation instead (on the staged
buffer for updates, directly on op->frames pre-registration for new
ops), so the installed frame is always atomically self-consistent.
bcm_rx_handler()'s RX_RTR_FRAME check now takes a lock-protected
snapshot of op->flags before deciding whether to call bcm_can_tx(),
but does not hold the lock across that call.
Also take a lock-protected snapshot of the currframe in bcm_can_tx()
to avoid partly overwrites by content updates in bcm_tx_setup().
Finally check if a TX_RESET_MULTI_IDX/SETTIMER might have reset
op->currframe between the two locked sections in bcm_can_tx().
Omit calling hrtimer_forward() with zero interval in bcm_rx_thr_handler().
kt_ival2 may have been concurrently cleared by bcm_rx_setup() before it
cancels this timer, so check kt_ival2 inside the bcm_rx_update_lock. |
| In the Linux kernel, the following vulnerability has been resolved:
can: bcm: add missing rcu list annotations and operations
sashiko-bot remarked the missing use of list_add_rcu() in
bcm_[rx|tx]_setup() to have a proper initialized bcm_op structure
when bcm_proc_show() traverses the bcm_op's under rcu_read_lock().
To cover all initial settings of the bcm_op's the list_add_rcu() calls
are moved to the end of the setup code.
While at it, also fix the mirroring removal side: bcm_release() called
bcm_remove_op() - which frees the op via call_rcu() - on ops that were
still linked in bo->tx_ops/bo->rx_ops, without list_del_rcu() first.
Unlink each op with list_del_rcu() before handing it to bcm_remove_op(),
matching the existing pattern in bcm_delete_tx_op()/bcm_delete_rx_op(). |
| In the Linux kernel, the following vulnerability has been resolved:
can: bcm: extend bcm_tx_lock usage for data and timer updates
Stage new CAN frame content for an existing tx op into a kmalloc()'d
buffer and validate it there, mirroring the approach already used in
bcm_rx_setup(). Only copy the validated data into op->frames while
holding op->bcm_tx_lock, so bcm_can_tx() and bcm_tx_timeout_handler()
can no longer observe a partially updated or unvalidated frame.
Add a missing error path for memcpy_from_msg() when copying CAN frame
data from userspace.
Also move the kt_ival1/kt_ival2/ival1/ival2 updates in bcm_tx_setup()
under op->bcm_tx_lock, and read kt_ival1/kt_ival2/count under the same
lock in bcm_tx_set_expiry() and bcm_tx_timeout_handler(), closing the
torn 64-bit ktime_t read on 32-bit platforms. |
| In the Linux kernel, the following vulnerability has been resolved:
can: bcm: fix stale rx/tx ops after device removal
RX: an RX_SETUP update(!) for an existing op skipped can_rx_register()
unconditionally, even when a concurrent NETDEV_UNREGISTER had already
torn down its registration (op->rx_reg_dev == NULL). This silently
did not re-enable frame delivery for that updated filter. bcm_rx_setup()
now re-registers in that case, while leaving rx_ops with ifindex = 0
(all CAN devices) which never carry a tracked rx_reg_dev registered as-is.
TX: bcm_notify() only handled bo->rx_ops on NETDEV_UNREGISTER, leaving
tx_ops with an active cyclic transmission re-arming its hrtimer
indefinitely to execute bcm_tx_timeout_handler(). Cancelling the hrtimer
prevents the runaway timer and any injection into a later reused ifindex,
since nothing else calls bcm_can_tx() for the op until an explicit
TX_SETUP update re-arms it.
Unlike bcm_rx_unreg(), which clears the tracked rx_reg_dev for rx_ops,
the ifindex is intentionally left unchanged for tx_ops. bcm_tx_setup()
always rejects ifindex 0, so clearing it would strand the op: neither a
later TX_SETUP (bcm_find_op()) nor TX_DELETE (bcm_delete_tx_op()) could
ever find it again, since both require an exact ifindex match. |
| In the Linux kernel, the following vulnerability has been resolved:
can: bcm: track a single source interface for ANYDEV timeout/throttle ops
An ANYDEV rx op (ifindex == 0) with an active RX timeout and/or
throttle timer has no defined semantics when matching frames arrive
from several interfaces: bcm_rx_handler() can run concurrently for
the same op on different CPUs, racing hrtimer_cancel()/
bcm_rx_starttimer() against bcm_rx_timeout_handler() and causing
spurious RX_TIMEOUT notifications and last_frames corruption. The
same concurrency lets throttled multiplex frames from different
interfaces clobber the single rx_ifindex/rx_stamp fields shared by
the op.
Add op->if_detected to track the first interface that delivers a
matching frame while a timeout/throttle timer is configured, and
reject frames from any other interface for that op. The claim is
decided in bcm_rx_handler() before hrtimer_cancel() touches
op->timer, so a rejected frame can never disturb the claimed
interface's watchdog. RTR-mode ops are excluded via RX_RTR_FRAME,
independent of kt_ival1/kt_ival2, since those may briefly hold a
stale value from an earlier non-RTR configuration.
The claim is released in bcm_notify() on NETDEV_UNREGISTER and in
bcm_rx_setup() when SETTIMER reconfigures the timer values.
A (re-)claim is only possible on CAN devices in NETREG_REGISTERED
dev->reg_state to cover the release in bcm_notify() where reg_state
becomes NETREG_UNREGISTERING until synchronize_net(). |
| In the Linux kernel, the following vulnerability has been resolved:
can: bcm: validate frame length in bcm_rx_setup() for RTR replies
bcm_tx_setup() validates cf->len against the CAN/CAN FD DLC limits
before installing frames for TX_SETUP, but bcm_rx_setup() never did
the same for the RTR-reply frame configured via RX_SETUP with
RX_RTR_FRAME. |
| In the Linux kernel, the following vulnerability has been resolved:
can: bcm: add missing device refcount for CAN filter removal
sashiko-bot remarked a problem with a concurrent device unregistration
in isotp.c which also is present in the bcm.c code. A former fix for raw.c
commit c275a176e4b6 ("can: raw: add missing refcount for memory leak fix")
introduced a netdevice_tracker which solves the issue for bcm.c too.
bcm_release(), bcm_delete_rx_op() and bcm_notifier() relied on
dev_get_by_index(ifindex) to re-find the device for an rx_op before
unregistering its filter. If a concurrent NETDEV_UNREGISTER has already
unlisted the device from the ifindex table, that lookup fails and
can_rx_unregister() is silently skipped, leaving a stale CAN filter
pointing at the soon-to-be-freed bcm_op/socket.
Hold a netdev_hold()/netdev_put() tracked reference on op->rx_reg_dev
from the moment the rx filter is registered in bcm_rx_setup() until it
is unregistered in bcm_rx_unreg(), and use that reference directly in
bcm_release() and bcm_delete_rx_op() instead of re-looking the device
up by ifindex. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Reset register bounds before narrowing retval range in check_mem_access()
When the BPF verifier processes a context load of an LSM hook return
value, it calls __mark_reg_s32_range() to narrow the register to the
hook's valid range. However, __mark_reg_s32_range() intersects the new
range with the register's existing bounds using max_t()/min_t() rather
than replacing them.
If the destination register carries stale bounds from a prior instruction
(e.g. BPF_MOV64_IMM), the intersection can produce a range narrower than
reality. The verifier then believes it knows the register's exact value,
while at runtime the actual hook return value is loaded, creating a
verifier/runtime mismatch that can be used to bypass BPF memory safety
checks.
The else branch already calls mark_reg_unknown() to reset register state
before any narrowing. Apply the same reset in the is_retval path so
stale bounds are cleared before __mark_reg_s32_range() intersects. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf,fork: wipe ->bpf_storage before bailouts that access it
Currently, copy_process() can bail out to free_task() before p->bpf_storage
has been initialized, with this call graph (shown here for the
!CONFIG_MEMCG case):
copy_process
dup_task_struct
arch_dup_task_struct
[copies the entire task_struct, including ->bpf_storage member]
[RLIMIT_NPROC check fails]
delayed_free_task
free_task
bpf_task_storage_free
rcu_dereference(task->bpf_storage)
bpf_local_storage_destroy
In this case, the nascent task's ->bpf_storage member that
bpf_local_storage_destroy() operates on is a plain copy of the parent's
->bpf_storage pointer, not a real initialized pointer.
This leads to badness (kernel hangs, UAF).
This is reachable as long as the process calling fork() has been inserted
into a task storage map. |
| In the Linux kernel, the following vulnerability has been resolved:
dibs: loopback: validate offset and size in move_data()
The loopback move_data() performs a memcpy into the registered DMB
without checking whether offset + size exceeds the DMB length. Unlike
real ISM hardware, which enforces memory region bounds natively, the
software loopback has no such protection.
A peer-supplied out-of-bounds offset or oversized write would result in
an OOB write past the allocated kernel buffer. Add an explicit bounds
check before the memcpy to reject such requests with -EINVAL. |
