| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/core: Validate cpu_id against nr_cpu_ids in DMAH alloc
The cpu_id attribute supplied by user space through
UVERBS_ATTR_ALLOC_DMAH_CPU_ID is passed directly to cpumask_test_cpu()
without first verifying that the value is within the valid CPU range.
Passing such untrusted data to cpumask_test_cpu() may lead to an
out-of-bounds read of the underlying cpumask bitmap: the helper expands
to a test_bit() that indexes the bitmap by cpu_id / BITS_PER_LONG with
no bound check.
In addition, on kernels built with CONFIG_DEBUG_PER_CPU_MAPS it trips
the WARN_ON_ONCE() in cpumask_check(); combined with panic_on_warn this
turns a bad user input into a machine reboot.
Reject any cpu_id that is not smaller than nr_cpu_ids with -EINVAL
before it is used.
Reported by Smatch. |
| In the Linux kernel, the following vulnerability has been resolved:
rxrpc: Fix the ACK parser to extract the SACK table for parsing
Fix modification of the received skbuff in rxrpc_input_soft_acks() and a
potential incorrect access of the buffer in a fragmented UDP packet (the
packet would probably have to be deliberately pre-generated as fragmented)
when AF_RXRPC tries to extract the contents of the SACK table by copying
out the contents of the SACK table into a buffer before attempting to parse
AF_RXRPC assumes that it can just call skb_condense() and then validly
access the SACK table from skb->data and that it will be a flat buffer -
but skb_condense() can silently fail to do anything under some
circumstances.
Note that whilst rxrpc_input_soft_acks() should be able to parse extended
ACKs, the rest of AF_RXRPC doesn't currently support that.
Further, there's then no need to call skb_condense() in rxrpc_input_ack(),
so don't. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: require Ethernet MAC header before using eth_hdr()
`ip6t_eui64`, `xt_mac`, the `bitmap:ip,mac`, `hash:ip,mac`, and
`hash:mac` ipset types, and `nf_log_syslog` access `eth_hdr(skb)`
after either assuming that the skb is associated with an Ethernet
device or checking only that the `ETH_HLEN` bytes at
`skb_mac_header(skb)` lie between `skb->head` and `skb->data`.
Make these paths first verify that the skb is associated with an
Ethernet device, that the MAC header was set, and that it spans at
least a full Ethernet header before accessing `eth_hdr(skb)`. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix same-register dst/src OOB read and pointer leak in sock_ops
When a BPF sock_ops program accesses ctx fields with dst_reg == src_reg,
the SOCK_OPS_GET_SK() and SOCK_OPS_GET_FIELD() macros fail to zero the
destination register in the !fullsock / !locked_tcp_sock path.
Both macros borrow a temporary register to check is_fullsock /
is_locked_tcp_sock when dst_reg == src_reg, because dst_reg holds the
ctx pointer. When the check is false (e.g., TCP_NEW_SYN_RECV state with
a request_sock), dst_reg should be zeroed but is not, leaving the stale
ctx pointer:
- SOCK_OPS_GET_SK: dst_reg retains the ctx pointer, passes NULL checks
as PTR_TO_SOCKET_OR_NULL, and can be used as a bogus socket pointer,
leading to stack-out-of-bounds access in helpers like
bpf_skc_to_tcp6_sock().
- SOCK_OPS_GET_FIELD: dst_reg retains the ctx pointer which the
verifier believes is a SCALAR_VALUE, leaking a kernel pointer.
Fix both macros by:
- Changing JMP_A(1) to JMP_A(2) in the fullsock path to skip the
added instruction.
- Adding BPF_MOV64_IMM(si->dst_reg, 0) after the temp register
restore in the !fullsock path, placed after the restore because
dst_reg == src_reg means we need src_reg intact to read ctx->temp. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix OOB in pcpu_init_value
An out-of-bounds read occurs when copying element from a
BPF_MAP_TYPE_CGROUP_STORAGE map to another pcpu map with the
same value_size that is not rounded up to 8 bytes.
The issue happens when:
1. A CGROUP_STORAGE map is created with value_size not aligned to
8 bytes (e.g., 4 bytes)
2. A pcpu map is created with the same value_size (e.g., 4 bytes)
3. Update element in 2 with data in 1
pcpu_init_value assumes that all sources are rounded up to 8 bytes,
and invokes copy_map_value_long to make a data copy, However, the
assumption doesn't stand since there are some cases where the source
may not be rounded up to 8 bytes, e.g., CGROUP_STORAGE, skb->data.
the verifier verifies exactly the size that the source claims, not
the size rounded up to 8 bytes by kernel, an OOB happens when the
source has only 4 bytes while the copy size(4) is rounded up to 8. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nfnetlink_osf: fix out-of-bounds read on option matching
In nf_osf_match(), the nf_osf_hdr_ctx structure is initialized once
and passed by reference to nf_osf_match_one() for each fingerprint
checked. During TCP option parsing, nf_osf_match_one() advances the
shared ctx->optp pointer.
If a fingerprint perfectly matches, the function returns early without
restoring ctx->optp to its initial state. If the user has configured
NF_OSF_LOGLEVEL_ALL, the loop continues to the next fingerprint.
However, because ctx->optp was not restored, the next call to
nf_osf_match_one() starts parsing from the end of the options buffer.
This causes subsequent matches to read garbage data and fail
immediately, making it impossible to log more than one match or logging
incorrect matches.
Instead of using a shared ctx->optp pointer, pass the context as a
constant pointer and use a local pointer (optp) for TCP option
traversal. This makes nf_osf_match_one() strictly stateless from the
caller's perspective, ensuring every fingerprint check starts at the
correct option offset. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_log: validate MAC header was set before dumping it
The fallback path of dump_mac_header() guards the MAC header access
only with "skb->mac_header != skb->network_header", without checking
skb_mac_header_was_set(). When the MAC header is unset, mac_header is
0xffff, so the test passes and skb_mac_header(skb) returns
skb->head + 0xffff, ~64 KiB past the buffer; the loop then reads
dev->hard_header_len bytes out of bounds into the kernel log.
This is reachable via the netdev logger: nf_log_unknown_packet() calls
dump_mac_header() unconditionally, and an skb sent through AF_PACKET
with PACKET_QDISC_BYPASS reaches the egress hook with mac_header still
unset (__dev_queue_xmit(), which would reset it, is bypassed).
Add the skb_mac_header_was_set() check the ARPHRD_ETHER path already
uses, and replace the open-coded MAC header length test with
skb_mac_header_len(). Only skbs with an unset MAC header are affected;
valid ones are dumped as before.
BUG: KASAN: slab-out-of-bounds in dump_mac_header (net/netfilter/nf_log_syslog.c:831)
Read of size 1 at addr ffff88800ea49d3f by task exploit/148
Call Trace:
kasan_report (mm/kasan/report.c:595)
dump_mac_header (net/netfilter/nf_log_syslog.c:831)
nf_log_netdev_packet (net/netfilter/nf_log_syslog.c:938 net/netfilter/nf_log_syslog.c:963)
nf_log_packet (net/netfilter/nf_log.c:260)
nft_log_eval (net/netfilter/nft_log.c:60)
nft_do_chain (net/netfilter/nf_tables_core.c:285)
nft_do_chain_netdev (net/netfilter/nft_chain_filter.c:307)
nf_hook_slow (net/netfilter/core.c:619)
nf_hook_direct_egress (net/packet/af_packet.c:257)
packet_xmit (net/packet/af_packet.c:280)
packet_sendmsg (net/packet/af_packet.c:3114)
__sys_sendto (net/socket.c:2265) |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: ebtables: fix OOB read in compat_mtw_from_user
Luxiao Xu says:
The function compat_mtw_from_user() converts ebtables extensions from
32-bit user structures to kernel native structures. However, it lacks
proper validation of the user-supplied match_size/target_size.
When certain extensions are processed, the kernel-side translation
logic may perform memory accesses based on the extension's expected
size. If the user provides a size smaller than what the extension
requires, it results in an out-of-bounds read as reported by KASAN.
This fix introduces a check to ensure match_size is at least as large
as the extension's required compatsize. This covers matches, watchers,
and targets, while maintaining compatibility with standard targets.
AFAIU this is relevant for matches that need to go though
match->compat_from_user() call. Those that use plain memcpy with the
user-provided size are ok because the caller checks that size vs the
start of the next rule entry offset (which itself is checked vs. total
size copied from userspace).
The ->compat_from_user() callbacks assume they can read compatsize bytes,
so they need this extra check.
Based on an earlier patch from Luxiao Xu. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Fix out-of-bounds stream encoder index v3
eng_id can be negative and that stream_enc_regs[]
can be indexed out of bounds.
eng_id is used directly as an index into stream_enc_regs[], which has
only 5 entries. When eng_id is 5 (ENGINE_ID_DIGF) or negative, this can
access memory past the end of the array.
Add a bounds check using ARRAY_SIZE() before using eng_id as an index.
The unsigned cast also rejects negative values.
This avoids out-of-bounds access.
Fixes the below smatch error:
dcn*_resource.c: stream_encoder_create() may index
stream_enc_regs[eng_id] out of bounds (size 5).
drivers/gpu/drm/amd/amdgpu/../display/dc/resource/dcn351/dcn351_resource.c
1246 static struct stream_encoder *dcn35_stream_encoder_create(
1247 enum engine_id eng_id,
1248 struct dc_context *ctx)
1249 {
...
1255
1256 /* Mapping of VPG, AFMT, DME register blocks to DIO block instance */
1257 if (eng_id <= ENGINE_ID_DIGF) {
ENGINE_ID_DIGF is 5. should <= be <?
Unrelated but, ugh, why is Smatch saying that "eng_id" can be negative?
end_id is type signed long, but there are checks in the caller which prevent it from being negative.
1258 vpg_inst = eng_id;
1259 afmt_inst = eng_id;
1260 } else
1261 return NULL;
1262
...
1281
1282 dcn35_dio_stream_encoder_construct(enc1, ctx, ctx->dc_bios,
1283 eng_id, vpg, afmt,
--> 1284 &stream_enc_regs[eng_id],
^^^^^^^^^^^^^^^^^^^^^^^ This stream_enc_regs[] array has 5 elements so we are one element beyond the end of the array.
...
1287 return &enc1->base;
1288 }
v2: use explicit bounds check as suggested by Roman/Dan; avoid unsigned int cast
v3: The compiler already knows how to compare the two values, so the
cast (int) is not needed. (Roman) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/vcn4: Prevent OOB reads when parsing IB
Rewrite the IB parsing to use amdgpu_ib_get_value() which handles the
bounds checks. |
| In the Linux kernel, the following vulnerability has been resolved:
smb/client: fix out-of-bounds read in smb2_compound_op()
If a server sends a truncated response but a large OutputBufferLength, and
terminates the EA list early, check_wsl_eas() returns success without
validating that the entire OutputBufferLength fits within iov_len.
Then smb2_compound_op() does:
memcpy(idata->wsl.eas, data[0], size[0]);
Where size[0] is OutputBufferLength. If iov_len is smaller than size[0],
memcpy can read beyond the end of the rsp_iov allocation and leak adjacent
kernel heap memory. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_event: Fix OOB read and infinite loop in hci_le_create_big_complete_evt
hci_le_create_big_complete_evt() iterates over BT_BOUND connections for
a BIG handle using a while loop, accessing ev->bis_handle[i++] on each
iteration. However, there is no check that i stays within ev->num_bis
before the array access.
When a controller sends a LE_Create_BIG_Complete event with fewer
bis_handle entries than there are BT_BOUND connections for that BIG,
or with num_bis=0, the loop reads beyond the valid bis_handle[] flex
array into adjacent heap memory. Since the out-of-bounds values
typically exceed HCI_CONN_HANDLE_MAX (0x0EFF), hci_conn_set_handle()
rejects them and the connection remains in BT_BOUND state. The same
connection is then found again by hci_conn_hash_lookup_big_state(),
creating an infinite loop with hci_dev_lock held.
Fix this by terminating the BIG if in case not all BIS could be setup
properly. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/rxe: Reject unknown opcodes before ICRC processing
Even after applying commit 7244491dab34 ("RDMA/rxe: Validate pad and ICRC
before payload_size() in rxe_rcv"), a single unauthenticated UDP packet
can still trigger panic. That patch handled payload_size() underflow only
for valid opcodes with short packets, not for packets carrying an unknown
opcode. The unknown-opcode OOB read described below predates that commit
and reaches back to the initial Soft RoCE driver.
The check added there reads
pkt->paylen < header_size(pkt) + bth_pad(pkt) + RXE_ICRC_SIZE
where header_size(pkt) expands to rxe_opcode[pkt->opcode].length. The
rxe_opcode[] array has 256 entries but is only populated for defined IB
opcodes; any other entry (for example opcode 0xff) is zero-initialized, so
length == 0 and the check degenerates to
pkt->paylen < 0 + bth_pad(pkt) + RXE_ICRC_SIZE
which does not constrain pkt->paylen enough. rxe_icrc_hdr() then computes
rxe_opcode[pkt->opcode].length - RXE_BTH_BYTES
which underflows when length == 0 and passes a huge value to rxe_crc32(),
causing an out-of-bounds read of the skb payload.
Reproduced on v7.0-rc7 with that fix applied, QEMU/KVM with
CONFIG_RDMA_RXE=y and CONFIG_KASAN=y, after
rdma link add rxe0 type rxe netdev eth0
A single 48-byte UDP packet to port 4791 with BTH opcode=0xff and
QPN=IB_MULTICAST_QPN triggers:
BUG: KASAN: slab-out-of-bounds in crc32_le+0x115/0x170
Read of size 1 at addr ...
The buggy address is located 0 bytes to the right of
allocated 704-byte region
Call Trace:
crc32_le+0x115/0x170
rxe_icrc_hdr.isra.0+0x226/0x300
rxe_icrc_check+0x13f/0x3a0
rxe_rcv+0x6e1/0x16e0
rxe_udp_encap_recv+0x20a/0x320
udp_queue_rcv_one_skb+0x7ed/0x12c0
Subsequent packets with the same shape fault on unmapped memory and panic
the kernel. The trigger requires only module load and "rdma link add"; no
QP, no connection, and no authentication.
Fix this by rejecting packets whose opcode has no rxe_opcode[] entry,
detected via the zero mask or zero length, before any length arithmetic
runs. |
| In the Linux kernel, the following vulnerability has been resolved:
erofs: fix the out-of-bounds nameoff handling for trailing dirents
Currently we already have boundary-checks for nameoffs, but the trailing
dirents are special since the namelens are calculated with strnlen()
with unchecked nameoffs.
If a crafted EROFS has a trailing dirent with nameoff >= maxsize,
maxsize - nameoff can underflow, causing strnlen() to read past the
directory block.
nameoff0 should also be verified to be a multiple of
`sizeof(struct erofs_dirent)` as well [1].
[1] https://sashiko.dev/#/patchset/20260416063511.3173774-1-hsiangkao%40linux.alibaba.com |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/uverbs: Validate wqe_size before using it in ib_uverbs_post_send
ib_uverbs_post_send() uses cmd.wqe_size from userspace without any
validation before passing it to kmalloc() and using the allocated
buffer as struct ib_uverbs_send_wr.
If a user provides a small wqe_size value (e.g., 1), kmalloc() will
succeed, but subsequent accesses to user_wr->opcode, user_wr->num_sge,
and other fields will read beyond the allocated buffer, resulting in
an out-of-bounds read from kernel heap memory. This could potentially
leak sensitive kernel information to userspace.
Additionally, providing an excessively large wqe_size can trigger a
WARNING in the memory allocation path, as reported by syzkaller.
This is inconsistent with ib_uverbs_unmarshall_recv() which properly
validates that wqe_size >= sizeof(struct ib_uverbs_recv_wr) before
proceeding.
Add the same validation for ib_uverbs_post_send() to ensure wqe_size
is at least sizeof(struct ib_uverbs_send_wr). |
| In the Linux kernel, the following vulnerability has been resolved:
libceph: Fix potential out-of-bounds access in ceph_handle_auth_reply()
This patch fixes an out-of-bounds access in ceph_handle_auth_reply()
that can be triggered by a message of type CEPH_MSG_AUTH_REPLY. In
ceph_handle_auth_reply(), the value of the payload_len field of such a
message is stored in a variable of type int. A value greater than
INT_MAX leads to an integer overflow and is interpreted as a negative
value. This leads to decrementing the pointer address by this value and
subsequently accessing it because ceph_decode_need() only checks that
the memory access does not exceed the end address of the allocation.
This patch fixes the issue by changing the data type of payload_len to
u32. Additionally, the data type of result_msg_len is changed to u32,
as it is also a variable holding a non-negative length.
Also, an additional layer of sanity checks is introduced, ensuring that
directly after reading it from the message, payload_len and
result_msg_len are not greater than the overall segment length.
BUG: KASAN: slab-out-of-bounds in ceph_handle_auth_reply+0x642/0x7a0 [libceph]
Read of size 4 at addr ffff88811404df14 by task kworker/20:1/262
CPU: 20 UID: 0 PID: 262 Comm: kworker/20:1 Not tainted 6.19.2 #5 PREEMPT(voluntary)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
Workqueue: ceph-msgr ceph_con_workfn [libceph]
Call Trace:
<TASK>
dump_stack_lvl+0x76/0xa0
print_report+0xd1/0x620
? __pfx__raw_spin_lock_irqsave+0x10/0x10
? kasan_complete_mode_report_info+0x72/0x210
kasan_report+0xe7/0x130
? ceph_handle_auth_reply+0x642/0x7a0 [libceph]
? ceph_handle_auth_reply+0x642/0x7a0 [libceph]
__asan_report_load_n_noabort+0xf/0x20
ceph_handle_auth_reply+0x642/0x7a0 [libceph]
mon_dispatch+0x973/0x23d0 [libceph]
? apparmor_socket_recvmsg+0x6b/0xa0
? __pfx_mon_dispatch+0x10/0x10 [libceph]
? __kasan_check_write+0x14/0x30i
? mutex_unlock+0x7f/0xd0
? __pfx_mutex_unlock+0x10/0x10
? __pfx_do_recvmsg+0x10/0x10 [libceph]
ceph_con_process_message+0x1f1/0x650 [libceph]
process_message+0x1e/0x450 [libceph]
ceph_con_v2_try_read+0x2e48/0x6c80 [libceph]
? __pfx_ceph_con_v2_try_read+0x10/0x10 [libceph]
? save_fpregs_to_fpstate+0xb0/0x230
? raw_spin_rq_unlock+0x17/0xa0
? finish_task_switch.isra.0+0x13b/0x760
? __switch_to+0x385/0xda0
? __kasan_check_write+0x14/0x30
? mutex_lock+0x8d/0xe0
? __pfx_mutex_lock+0x10/0x10
ceph_con_workfn+0x248/0x10c0 [libceph]
process_one_work+0x629/0xf80
? __kasan_check_write+0x14/0x30
worker_thread+0x87f/0x1570
? __pfx__raw_spin_lock_irqsave+0x10/0x10
? __pfx_try_to_wake_up+0x10/0x10
? kasan_print_address_stack_frame+0x1f7/0x280
? __pfx_worker_thread+0x10/0x10
kthread+0x396/0x830
? __pfx__raw_spin_lock_irq+0x10/0x10
? __pfx_kthread+0x10/0x10
? __kasan_check_write+0x14/0x30
? recalc_sigpending+0x180/0x210
? __pfx_kthread+0x10/0x10
ret_from_fork+0x3f7/0x610
? __pfx_ret_from_fork+0x10/0x10
? __switch_to+0x385/0xda0
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1a/0x30
</TASK>
[ idryomov: replace if statements with ceph_decode_need() for
payload_len and result_msg_len ] |
| In the Linux kernel, the following vulnerability has been resolved:
libceph: prevent potential out-of-bounds reads in process_message_header()
If the message frame is (maliciously) corrupted in a way that the
length of the control segment ends up being less than the size of the
message header or a different frame is made to look like a message
frame, out-of-bounds reads may ensue in process_message_header().
Perform an explicit bounds check before decoding the message header. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe: Add bounds check on pat_index to prevent OOB kernel read in madvise
When user provides a bogus pat_index value through the madvise IOCTL, the
xe_pat_index_get_coh_mode() function performs an array access without
validating bounds. This allows a malicious user to trigger an out-of-bounds
kernel read from the xe->pat.table array.
The vulnerability exists because the validation in madvise_args_are_sane()
directly calls xe_pat_index_get_coh_mode(xe, args->pat_index.val) without
first checking if pat_index is within [0, xe->pat.n_entries).
Although xe_pat_index_get_coh_mode() has a WARN_ON to catch this in debug
builds, it still performs the unsafe array access in production kernels.
v2(Matthew Auld)
- Using array_index_nospec() to mitigate spectre attacks when the value
is used
v3(Matthew Auld)
- Put the declarations at the start of the block
(cherry picked from commit 944a3329b05510d55c69c2ef455136e2fc02de29) |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_conntrack_h323: fix OOB read in decode_choice()
In decode_choice(), the boundary check before get_len() uses the
variable `len`, which is still 0 from its initialization at the top of
the function:
unsigned int type, ext, len = 0;
...
if (ext || (son->attr & OPEN)) {
BYTE_ALIGN(bs);
if (nf_h323_error_boundary(bs, len, 0)) /* len is 0 here */
return H323_ERROR_BOUND;
len = get_len(bs); /* OOB read */
When the bitstream is exactly consumed (bs->cur == bs->end), the check
nf_h323_error_boundary(bs, 0, 0) evaluates to (bs->cur + 0 > bs->end),
which is false. The subsequent get_len() call then dereferences
*bs->cur++, reading 1 byte past the end of the buffer. If that byte
has bit 7 set, get_len() reads a second byte as well.
This can be triggered remotely by sending a crafted Q.931 SETUP message
with a User-User Information Element containing exactly 2 bytes of
PER-encoded data ({0x08, 0x00}) to port 1720 through a firewall with
the nf_conntrack_h323 helper active. The decoder fully consumes the
PER buffer before reaching this code path, resulting in a 1-2 byte
heap-buffer-overflow read confirmed by AddressSanitizer.
Fix this by checking for 2 bytes (the maximum that get_len() may read)
instead of the uninitialized `len`. This matches the pattern used at
every other get_len() call site in the same file, where the caller
checks for 2 bytes of available data before calling get_len(). |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: xt_tcpmss: check remaining length before reading optlen
Quoting reporter:
In net/netfilter/xt_tcpmss.c (lines 53-68), the TCP option parser reads
op[i+1] directly without validating the remaining option length.
If the last byte of the option field is not EOL/NOP (0/1), the code attempts
to index op[i+1]. In the case where i + 1 == optlen, this causes an
out-of-bounds read, accessing memory past the optlen boundary
(either reading beyond the stack buffer _opt or the
following payload). |
