| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
Input: synaptics-rmi4 - fix F55 transmitter electrode count typo
During F55 sensor detection, the transmitter (TX) electrode count was
incorrectly assigned the value of the receiver (RX) electrode count
due to copy-paste typos.
This incorrect value was then propagated to the driver data and used
by F54 to determine the diagnostics report size. On devices with more
RX than TX electrodes, this inflated the perceived TX count, leading
to incorrect report size calculations and potential out-of-bounds
buffer accesses.
Fix the typos by correctly assigning the TX electrode counts. |
| In the Linux kernel, the following vulnerability has been resolved:
fbdev: bound mode sysfs output to the sysfs buffer
mode_string() uses snprintf() which can return a value larger than the
remaining buffer space. show_modes() accumulates the return value into i
without checking whether i has reached PAGE_SIZE, causing the offset to
advance past the sysfs buffer if the modelist is long enough.
Add a size parameter to mode_string() and use scnprintf() to return
only the bytes actually written. Add an early return when offset
already exceeds the buffer. In show_modes(), stop accumulating once
the buffer is full. |
| In the Linux kernel, the following vulnerability has been resolved:
net/atm: fix slab-out-of-bounds read in vcc_setsockopt()
vcc_setsockopt() contained an ineffective optlen check:
if (__SO_LEVEL_MATCH(optname, level) && optlen != __SO_SIZE(optname))
return -EINVAL;
If __SO_LEVEL_MATCH(optname, level) evaluated to false (e.g. if the caller
passed a mismatched level), the length check optlen != __SO_SIZE(optname)
was short-circuited and bypassed. Execution then fell through to switch(optname),
calling copy_from_sockptr() assuming optval contained sufficient space.
Furthermore, even if level matched, a cgroup BPF setsockopt filter could shrink
optlen after entry. Because copy_from_sockptr() on kernel pointers uses memcpy(),
this leads to a KASAN slab-out-of-bounds read when optlen is smaller than the
expected structure size.
Fix this by using copy_safe_from_sockptr(), which unconditionally validates
that optlen is at least the expected size before copying. Also change the local
'value' variable type from 'unsigned long' to 'int' so that SO_SETCLP matches
its sizeof(int) ABI encoding on 64-bit systems. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix missing shared-key auth challenge length check
The WEP shared-key authentication handler uses the challenge-text
element's attacker-controlled length without checking it against the
fixed 128-byte chg_txt buffer.
In OnAuthClient() the length from rtw_get_ie() - up to 255 - is used
to perform memcpy() into the 128-byte pmlmeinfo->chg_txt, so a
malicious AP sending a malformed WLAN_EID_CHALLENGE element can
overflow/underfill chg_txt by up to 127 bytes. It is reachable over the
air, before association, during shared-key authentication. In the case
of an overflow, the driver can write out of bounds. In the case of an
underfill, the driver can echo stale buffer memory.
The challenge text is defined to be exactly 128 octets, which is
already provided as the WLAN_AUTH_CHALLENGE_LEN define; require the
element to be exactly that length before use. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: libiscsi_tcp: Bound SCSI Response data segment to the connection buffer
iscsi_tcp_hdr_dissect() receives the data segment of several PDU types
into the fixed-size conn->data buffer, which is allocated for
ISCSI_DEF_MAX_RECV_SEG_LEN (8192) bytes. For the LOGIN_RSP, TEXT_RSP,
REJECT and ASYNC_EVENT opcodes the dissect path already rejects a PDU
whose DataSegmentLength exceeds that buffer.
The SCSI Command Response (ISCSI_OP_SCSI_CMD_RSP) path also copies its
data segment (sense/response data) into conn->data via
iscsi_tcp_data_recv_prep(), but it does so without the same check. The
only upstream bound on in.datalen is conn->max_recv_dlength, the
initiator's advertised MaxRecvDataSegmentLength, which is commonly
negotiated well above 8192 (open-iscsi defaults to 262144). A target
that returns a SCSI Response with a DataSegmentLength between 8193 and
max_recv_dlength therefore overflows the 8192-byte conn->data buffer.
Once the same bound applies, ISCSI_OP_SCSI_CMD_RSP is handled exactly
like those responses: bound the data segment, receive it into conn->data
when present, and otherwise complete the PDU with no data. Fold the
opcode into that case group rather than duplicating the check. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: SOF: ipc3-control: Validate size in snd_sof_update_control
In snd_sof_update_control(), firmware-provided cdata->num_elems is
checked against local_cdata->data->size but never against the actual
allocation size. If local_cdata->data->size was previously set to an
inconsistent value, the memcpy could write past the allocated buffer.
Add a bounds check to ensure num_elems fits within the available space
in the ipc_control_data allocation before copying. |
| In the Linux kernel, the following vulnerability has been resolved:
ntfs3: bound to_move in indx_insert_into_root before hdr_insert_head
indx_insert_into_root() promotes a full resident $INDEX_ROOT into
$INDEX_ALLOCATION and copies all non-last resident root entries into
a newly allocated INDEX_BUFFER via hdr_insert_head(). The source
byte count 'to_move' is summed from the on-disk resident entry sizes
and is independent of the destination buffer size, which comes from
root->index_block_size (via indx->index_bits).
A crafted NTFS image that keeps a valid, full resident root but
shrinks root->index_block_size down to 512 after the root has been
populated makes hdr_insert_head() memcpy attacker-controlled resident
entry bytes past the end of the kmalloc(1u << indx->index_bits)
allocation returned by indx_new(). For a 512-byte destination and a
resident root whose non-last entries total 560 bytes, the memcpy
overruns by 120 bytes and a following memmove extends the highest
written offset to 136 bytes past the allocation. The overflow bytes
are a direct copy of on-disk entries (via kmemdup), so they are
fully attacker-controlled.
The write is reachable from unprivileged open(O_CREAT) on a mounted
crafted NTFS image: a single sufficiently long create in a directory
whose resident root is already full forces root promotion and
triggers the copy.
This is a controlled out-of-bounds write of 120-136 bytes past a
kmalloc(index_block_size) allocation, with attacker-controlled
content. It is a bounded adjacent-heap corruption primitive; it is
not an arbitrary-address write. Successful exploitation into a named
victim object depends on the surrounding slab layout.
Reject the copy at the sink. The destination's INDEX_HDR already
reports hdr_total (the payload capacity of the new buffer) and
hdr_used (the bytes already consumed by the terminal END entry
installed by indx_new()); require that to_move fits in the remaining
payload before calling hdr_insert_head(). On mismatch, fail with
-EINVAL and mark the filesystem as having a detected on-disk
inconsistency, which is the same behaviour as the surrounding
validation in this function. |
| In the Linux kernel, the following vulnerability has been resolved:
cpu: hotplug: Bound hotplug states sysfs output
states_show() adds CPU hotplug state names into a single sysfs buffer
using sprintf(). With enough registered states, this can write past the
end of the PAGE_SIZE buffer.
Use sysfs_emit_at() so output is bounded. |
| Misuse and misconfiguration in Bluetooth communication in SwitchBot Door Lock Series allows an attacker to bypass the electronic lock and access controls via a manipulated communication protocol. |
| A vulnerability was detected in turboderp ExLlamaV2 up to 0.3.2. Affected is the function STFile.get_tensor of the file exllamav2/stloader.py of the component Safetensors Tensor Loader. Performing a manipulation of the argument data_offsets results in buffer overflow. The attack is possible to be carried out remotely. The exploit is now public and may be used. The project was informed of the problem early through an issue report but has not responded yet. |
| SODOLA SL902-SWTGW124AS firmware before 200.2.12 contains a buffer overflow vulnerability that allows unauthenticated remote attackers to cause a denial of service by sending an oversized boundary value in the Content-Type header of a crafted POST request. Attackers can exploit the embedded HTTP server's multipart/form-data boundary parser to cause the device to become fully unresponsive — dropping all management access and traffic forwarding during its self-recovery cycle. |
| A flaw has been found in Edimax BR-6208AC 1.32. Affected by this issue is some unknown functionality of the file /goform/formWlSiteSurvey. This manipulation of the argument ifname causes buffer overflow. Remote exploitation of the attack is possible. The exploit has been published and may be used. The vendor was contacted early about this disclosure but did not respond in any way. This vulnerability only affects products that are no longer supported by the maintainer. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/zcrypt: Improve EP11 CPRB length and overflow checks
The xcrb_msg_to_type6_ep11cprb_msgx() function lacks proper input
validation, creating security vulnerabilities:
1. Missing minimum size validation: The ep11_cprb structure and
subsequent payload fields (pld_tag, pld_lenfmt) are copied from
userspace without verifying sufficient buffer length.
2. Arithmetic overflow in length calculations: CEIL4 alignment could
overflow, bypassing size checks and enabling buffer overflows.
3. The payload is asn1 encoded but the function just uses a simple c
struct overlay to access some fields of the payload.
Fix by using size_t for length calculations, adding U32_MAX boundary
checks after alignment, and validating minimum request size and
minimum reply size before copying from userspace. Do a very simple
asn1 parsing of the payload up to the function value field. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: ti-adc161s626: use DMA-safe memory for spi_read()
Add a DMA-safe buffer and use it for spi_read() instead of a stack
memory. All SPI buffers must be DMA-safe.
Since we only need up to 3 bytes, we just use a u8[] instead of __be16
and __be32 and change the conversion functions appropriately. |
| In the Linux kernel, the following vulnerability has been resolved:
NFC: digital: Bounds check NFC-A cascade depth in SDD response handler
The NFC-A anti-collision cascade in digital_in_recv_sdd_res() appends 3
or 4 bytes to target->nfcid1 on each round, but the number of cascade
rounds is controlled entirely by the peer device. The peer sets the
cascade tag in the SDD_RES (deciding 3 vs 4 bytes) and the
cascade-incomplete bit in the SEL_RES (deciding whether another round
follows).
ISO 14443-3 limits NFC-A to three cascade levels and target->nfcid1 is
sized accordingly (NFC_NFCID1_MAXSIZE = 10), but nothing in the driver
actually enforces this. This means a malicious peer can keep the
cascade running, writing past the heap-allocated nfc_target with each
round.
Fix this by rejecting the response when the accumulated UID would exceed
the buffer.
Commit e329e71013c9 ("NFC: nci: Bounds check struct nfc_target arrays")
fixed similar missing checks against the same field on the NCI path. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: act_ife: Fix metalist update behavior
Whenever an ife action replace changes the metalist, instead of
replacing the old data on the metalist, the current ife code is appending
the new metadata. Aside from being innapropriate behavior, this may lead
to an unbounded addition of metadata to the metalist which might cause an
out of bounds error when running the encode op:
[ 138.423369][ C1] ==================================================================
[ 138.424317][ C1] BUG: KASAN: slab-out-of-bounds in ife_tlv_meta_encode (net/ife/ife.c:168)
[ 138.424906][ C1] Write of size 4 at addr ffff8880077f4ffe by task ife_out_out_bou/255
[ 138.425778][ C1] CPU: 1 UID: 0 PID: 255 Comm: ife_out_out_bou Not tainted 7.0.0-rc1-00169-gfbdfa8da05b6 #624 PREEMPT(full)
[ 138.425795][ C1] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[ 138.425800][ C1] Call Trace:
[ 138.425804][ C1] <IRQ>
[ 138.425808][ C1] dump_stack_lvl (lib/dump_stack.c:122)
[ 138.425828][ C1] print_report (mm/kasan/report.c:379 mm/kasan/report.c:482)
[ 138.425839][ C1] ? srso_alias_return_thunk (arch/x86/lib/retpoline.S:221)
[ 138.425844][ C1] ? __virt_addr_valid (./arch/x86/include/asm/preempt.h:95 (discriminator 1) ./include/linux/rcupdate.h:975 (discriminator 1) ./include/linux/mmzone.h:2207 (discriminator 1) arch/x86/mm/physaddr.c:54 (discriminator 1))
[ 138.425853][ C1] ? ife_tlv_meta_encode (net/ife/ife.c:168)
[ 138.425859][ C1] kasan_report (mm/kasan/report.c:221 mm/kasan/report.c:597)
[ 138.425868][ C1] ? ife_tlv_meta_encode (net/ife/ife.c:168)
[ 138.425878][ C1] kasan_check_range (mm/kasan/generic.c:186 (discriminator 1) mm/kasan/generic.c:200 (discriminator 1))
[ 138.425884][ C1] __asan_memset (mm/kasan/shadow.c:84 (discriminator 2))
[ 138.425889][ C1] ife_tlv_meta_encode (net/ife/ife.c:168)
[ 138.425893][ C1] ? ife_tlv_meta_encode (net/ife/ife.c:171)
[ 138.425898][ C1] ? srso_alias_return_thunk (arch/x86/lib/retpoline.S:221)
[ 138.425903][ C1] ife_encode_meta_u16 (net/sched/act_ife.c:57)
[ 138.425910][ C1] ? __pfx_do_raw_spin_lock (kernel/locking/spinlock_debug.c:114)
[ 138.425916][ C1] ? __asan_memcpy (mm/kasan/shadow.c:105 (discriminator 3))
[ 138.425921][ C1] ? __pfx_ife_encode_meta_u16 (net/sched/act_ife.c:45)
[ 138.425927][ C1] ? srso_alias_return_thunk (arch/x86/lib/retpoline.S:221)
[ 138.425931][ C1] tcf_ife_act (net/sched/act_ife.c:847 net/sched/act_ife.c:879)
To solve this issue, fix the replace behavior by adding the metalist to
the ife rcu data structure. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: avoid buffer overflow attach in smu_sys_set_pp_table()
It malicious user provides a small pptable through sysfs and then
a bigger pptable, it may cause buffer overflow attack in function
smu_sys_set_pp_table(). |
| When libcurl is asked to perform automatic gzip decompression of
content-encoded HTTP responses with the `CURLOPT_ACCEPT_ENCODING` option,
**using zlib 1.2.0.3 or older**, an attacker-controlled integer overflow would
make libcurl perform a buffer overflow. |
| gio/gsocks4aproxy.c in GNOME GLib before 2.82.1 has an off-by-one error and resultant buffer overflow because SOCKS4_CONN_MSG_LEN is not sufficient for a trailing '\0' character. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: scomp - fix req->dst buffer overflow
The req->dst buffer size should be checked before copying from the
scomp_scratch->dst to avoid req->dst buffer overflow problem. |
