| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
sched/fair: Fix overflow in update_tg_cfs_runnable()
A divide-by-zero crash is observed when running hackbench:
[14697.488452] CPU: 112 UID: 0 PID: 124791 Comm: hackbench Not tainted 7.1.0-rc2+
[14697.492627] RIP: 0010:propagate_entity_load_avg+0x35f/0x3e0
[14697.506799] <TASK>
[14697.507411] __dequeue_task+0x2b4/0xc70
[14697.508677] dequeue_task_fair+0x36/0x370
[14697.509047] dequeue_task+0x101/0x2f0
[14697.509426] __schedule+0x1b1/0x1a00
[14697.510868] anon_pipe_read+0x3da/0x450
[14697.511400] vfs_read+0x361/0x390
[14697.512053] __x64_sys_read+0x19/0x30
The divide-by-zero happens here:
if (scale_load_down(gcfs_rq->load.weight)) {
load_sum = div_u64(gcfs_rq->avg.load_sum,
scale_load_down(gcfs_rq->load.weight));
}
gcfs_rq->load.weight is an insane large value and is truncated
to the lower 32 bits by div_u64, which happen to be 0.
Using AI for investigation, the cause is a u32 overflow in
update_tg_cfs_runnable(), and flat pickup became a victim when using
tg_tasks():
u32 new_sum, divider;
...
new_sum = se->avg.runnable_avg * divider; <-- boom
The following sequence shows how this triggers the crash:
propagate_entity_load_avg()
update_tg_cfs_runnable() # u32 overflow corrupts runnable_sum
__update_load_avg_cfs_rq()
___update_load_avg() # computes insane runnable_avg
update_tg_load_avg() # propagates to tg->runnable_avg
update_cfs_group()
calc_concur_shares()
tg_tasks() # long-to-int truncation, negative nr
reweight_entity() # corrupted se->load.weight
update_load_add() # corrupted cfs_rq->load.weight
propagate_entity_load_avg()
update_tg_cfs_load()
div_u64() # divide-by-zero
Fix by widening new_sum from u32 to u64 (no need to force tg_tasks()
to return unsigned long after this fix) |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: fsl_audmix: rework runtime PM handling in probe
After pm_runtime_enable() the AUDMIX block is powered off and stays
suspended until the first runtime resume. Register writes issued between
probe() and the first resume (e.g. from DAPM or ALSA control paths)
target unpowered hardware and cause a system hang.
Fix this by calling pm_runtime_resume_and_get() immediately after
pm_runtime_enable() to power the hardware up and enable its clocks.
Release the reference afterwards with pm_runtime_put() to allow the
runtime PM framework to suspend the device and switch the regmap to
cache-only mode when idle.
When CONFIG_PM is disabled or runtime PM is not enabled, pm_runtime_*
calls are stubs that do not power up the hardware. Handle this case
explicitly by calling fsl_audmix_runtime_resume() directly so the
hardware is always initialised and its clocks are enabled, ensuring
register accesses succeed regardless of PM configuration. |
| In the Linux kernel, the following vulnerability has been resolved:
dm-pcache: validate the persisted dirty_tail chain at load
The writeback worker follows the persisted dirty_tail chain, which is
decoded from the cache device independently of the key_tail chain that
cache_replay() walks and bounds. A crafted image, whose on-media fields are
authenticated only by a crc32c with a fixed seed, can aim dirty_tail at a
chain of last ksets that never terminates, so cache_writeback_fn() re-arms
itself with no delay forever.
Walk the dirty_tail chain once at load with the same hop cap cache_replay()
uses and fail the table load with -EIO if it does not reach an end within
n_segs hops. |
| go-openapi/swag jsonutils before 0.27.1 contains a stack overflow vulnerability in ordered JSON parsing and serialization due to unbounded recursion with no depth limit. Remote unauthenticated attackers can submit deeply nested JSON documents to services accepting OpenAPI specifications, causing fatal stack overflow that terminates the process and all in-flight requests. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: rk3288 - fail ahash requests on HASH idle timeout
rk_hash_run() waits for RK_CRYPTO_HASH_STS to become idle after the
final DMA transfer, but ignores the poll result. If the hash engine
never becomes idle, the driver still reads the digest registers and
finalizes the request with the previous success value.
Store the poll result and finalize the request with the timeout error
before reading the digest registers. |
| In the Linux kernel, the following vulnerability has been resolved:
hwrng: xilinx-trng - propagate timeout before any data is read
xtrng_readblock32() polls for 16-byte chunks but returns the number of
bytes read even when the first poll times out. Its caller then treats a
zero return as a short successful read, and partial reads for full
32-byte blocks can make the tail copy use a fixed block offset rather
than the amount already produced.
Return the poll error when no data has been read, preserve partial
positive returns after some data is available, stop the generator on all
collection exits, and append tail bytes at the current output count. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: atmel-ecc - reject hardware ECDH without a public key
The hardware ECDH path in atmel_ecdh_compute_shared_secret() uses the
private key stored in the device. However, the public key is cached only
after atmel_ecdh_set_secret() successfully generated that private key
for the current tfm.
atmel_ecdh_generate_public_key() already rejects requests when no public
key is cached. Add the same check to atmel_ecdh_compute_shared_secret()
to prevent the device from using a private key that was not generated
for the current tfm. |
| In the Linux kernel, the following vulnerability has been resolved:
firmware: arm_scmi: Unwind P2A receiver mailbox setup failure
mailbox_chan_setup() can request an additional P2A receiver channel after
successfully acquiring the primary P2A channel. If that later request
fails, the function returns immediately and leaves the primary channel
allocated.
Unwind the primary mailbox channel before returning the error so probe
deferral or other setup failures do not leave the channel busy for later
probe attempts. |
| In the Linux kernel, the following vulnerability has been resolved:
cxl/mbox: Break poison list loop on an empty payload
A device that returns count == 0 with CXL_POISON_FLAG_MORE set on every
iteration never advances nr_records, so the max_errors guard never
trips and the do/while loops forever while holding poison.mutex. That
hangs the sysfs-triggered scan thread and blocks all subsequent poison
operations on the device. The existing "Protect against an uncleared
_FLAG_MORE" guard was intended to bound a misbehaving device but does
not cover the count == 0 case.
Stop the loop on an empty payload so a malfunctioning or malicious
device cannot wedge the poison scan. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/hfi1: Preserve unit 0 on allocation failure
hfi1_free_devdata() assumes that the device was inserted into the unit
table and unconditionally erases dd->unit. If xa_alloc_irq() fails, the
zero-initialized unit remains zero, so full cleanup can remove an
unrelated device from index 0.
Release only the rdmavt allocation and return immediately while the unit
table has not acquired the device. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Reject arena frees below the arena base
bpf_arena_free_pages() accepts scalar arena addresses. The runtime
masks the address to the low 32 bits and reconstructs a full user
address from the arena base before returning the range to the arena
free tree.
When the scalar value is below the low 32 bits of the arena base,
full_uaddr falls below user_vm_start. The existing upper-end clipping
then turns this into an out-of-range free-tree offset. A later
allocation can reuse that offset and return an address below the arena
mapping.
Reject such frees before computing the clipped range. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/bnxt_re: Clear VM_MAYWRITE on DBR/toggle page mmap
bnxt_re_mmap() rejects VM_WRITE for the DBR_PAGE and TOGGLE_PAGE mmap
flags, but a read-only mapping can still retain VM_MAYWRITE. nd later
be upgraded with mprotect(PROT_WRITE). This can bypass the write check
that only runs at mmap time.
Clear VM_MAYWRITE before vm_insert_page() in the shared DBR/toggle-page
branch, matching the existing policy that userspace writes are not
expected for these pages. |
| In the Linux kernel, the following vulnerability has been resolved:
dax/fsdev: clear vmemmap_shift when binding static pgmap
Clear pgmap->vmemmap_shift for static DAX devices. When rebinding a static
device from device_dax (which may set vmemmap_shift based on alignment) to
fsdev_dax, the stale vmemmap_shift persists on the shared pgmap. Explicitly
zero it before devm_memremap_pages() so the vmemmap is built for order-0
folios as fsdev requires. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: clear stale xarray tags on folios skipped during writeback
In data=journal mode, the writeback thread can hit the
WARN_ON_ONCE(sb_rdonly(sb)) in ext4_journal_check_start() while the
superblock is being remounted read-only during reboot:
Workqueue: writeback wb_workfn (flush-253:0)
RIP: 0010:ext4_journal_check_start+0x8b/0xd0
Call Trace:
__ext4_journal_start_sb+0x3c/0x1e0
mpage_prepare_extent_to_map+0x4af/0x580
ext4_do_writepages+0x3c0/0x1080
ext4_writepages+0xc8/0x1a0
do_writepages+0xc4/0x180
__writeback_single_inode+0x45/0x2f0
writeback_sb_inodes+0x26b/0x5d0
__writeback_inodes_wb+0x54/0x100
wb_writeback+0x1ac/0x320
wb_workfn+0x394/0x470
And followed by the warning:
EXT4-fs warning (device vda1): ext4_evict_inode:195: inode #6263:
comm (sd-umount): data will be lost
This issue is not reproduced every time, but frequently.
The reproduction step is to create a VM with 8 CPUs, 16G memory and
setup data=journal:
sudo tune2fs -o journal_data /dev/vda1
Run fio:
rm -f fiotest
fio --name=fiotest --rw=randwrite --bs=4k --runtime=6 --ioengine=libaio
--iodepth=256 --numjobs=8 --filename=fiotest --filesize=30G
--group_reporting
Reboot the VM, and check the console output from:
virsh console testvm
But there is no dirty inode, folio_clear_dirty_for_io clears PG_dirty
but leaves tags PAGECACHE_TAG_DIRTY and PAGECACHE_TAG_TOWRITE set which
are only cleared by __folio_start_writeback.
In data=journal mode, jbd2 checkpoints the journalled data to its final
location and clears its own dirty flag without touching folio PG_dirty
or xarray dirty flags.
The commit f4a2b42e7891 ("ext4: fix stale xarray tags after writeback")
fixes when PG_dirty is still set but there is no dirty page.
Another case is PG_dirty is cleared, but PAGECACHE_TAG_DIRTY and
PAGECACHE_TAG_TOWRITE is still set. In this case, writeback thread
checks clean folio and skips it in mpage_prepare_extent_to_map:
if (!folio_test_dirty(folio) ||
...
folio_unlcok(folio);
continue
And never reaches ext4_bio_write_folio where the commit f4a2b42e7891
clears the stale xarray tags. Print debug logs after the filesystem
is remounted read-only:
writepages RDONLY nrpages=2048 dirtytag=1 wbtag=0 towrite=1 sync=0
And all folios are actually clean:
folio idx=3 dirty=0 wb=0 checked=0 dirtybuf=0 jbddirty=0 mapped=1
...
We need to clear the xarray stale tags for such clean folios by
cycling them through writeback in the skip path, the same way
f4a2b42e7891 does in ext4_bio_write_folio. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Preserve unique-field state across nested structs
btf_find_struct_field() initializes a fresh seen mask for every recursive
descent. Unique special fields in different levels of the same aggregate
therefore do not see one another. The duplicate fields can reach
btf_parse_fields(), where they trigger an invariant WARN_ON_ONCE(). A
crafted user BTF can consequently trigger the warning before map creation
checks capabilities.
Initialize the seen mask once in btf_find_field() and pass the same pointer
through struct, datasec, and nested-struct walks. This gives the entire field
traversal one shared uniqueness state. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/tegra241-cmdqv: Don't run the error ISR before probe sets up vintfs
__tegra241_cmdqv_probe() requests the error IRQ before it has allocated the
cmdqv->vintfs array and set cmdqv->num_vintfs. A CMDQV left enabled with a
latched error across a kexec fires the IRQ as soon as it is requested, and
tegra241_cmdqv_isr() then walks the uninitialized cmdqv->vintfs array.
Request the IRQ only after cmdqv->vintfs is allocated and zeroed, so that
a latched interrupt firing early runs the ISR against a valid array of NULL
slots that it safely skips. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: bound TLV walk in mt7996_mcu_get_chip_config
The response TLV loop advanced by tlv->len without a minimum, so a
theoretical firmware response containing a zero-length TLV could spin
forever, hanging the CPU during device probe.
The u32 payload was also read without bounds checking.
Reject a short fixed field, stop on a TLV whose length underruns the
header or overruns the skb. |
| In the Linux kernel, the following vulnerability has been resolved:
i3c: dw: avoid shift-out-of-bounds when DAA assigns no devices
On an empty bus ENTDAA assigns nothing, so cmd->rx_len (the count
of addresses left unassigned) equals master->maxdevs.
The GENMASK() index master->maxdevs - cmd->rx_len - 1 then becomes -1,
which trips up UBSAN. This happens every time on boot on a Gigabyte/AMD
server:
UBSAN: shift-out-of-bounds in drivers/i3c/master/dw-i3c-master.c:905:12
shift exponent 64 is too large for 64-bit type 'long unsigned int'
CPU: 7 UID: 0 PID: 963 Comm: (udev-worker) Not tainted 7.0.11-200.fc44.x86_64 #1 PREEMPT(lazy)
Hardware name: Giga Computing E163-Z34-AAH1-000/MZ33-DC1-000, BIOS R32_F45 04/01/2026
Call Trace:
<TASK>
dump_stack_lvl+0x5d/0x80
ubsan_epilogue+0x5/0x2b
__ubsan_handle_shift_out_of_bounds.cold+0xd7/0x1ab
dw_i3c_master_daa.cold+0x1b/0x96 [dw_i3c_master]
i3c_master_do_daa_ext.part.0+0x3e/0xf0 [i3c]
Skip the mask when no new device was assigned. |
| In the Linux kernel, the following vulnerability has been resolved:
md/bitmap: resume array on backlog_store() error path
backlog_store() suspends the array before checking whether a write-mostly
device exists. If no such device exists, the error path only unlocks
reconfig_mutex and leaves the array suspended, blocking subsequent I/O.
Use mddev_unlock_and_resume() to release both states. |
| In the Linux kernel, the following vulnerability has been resolved:
phy: qcom: qmp-usb-legacy: Fix possible NULL-deref on early runtime suspend
There is a small window where the runtime suspend callback may run
after pm_runtime_enable() and before pm_runtime_forbid(). In this
case, a crash occurs because runtime suspend/resume dereferences
qmp->phy pointer, which is not yet initialized:
`if (!qmp->phy->init_count) {`
This can also happen if user re-enables runtime-pm via the sysfs
attribute before qmp phy is initialized.
Similarly to other qcom phy drivers, introduce a qmp->phy_initialized
variable that can be used to avoid relying on the possibly uninitialized
phy pointer. |
